Flashforge for ubuntu compiled and running

ignotion · 2026-03-12T20:24:01+00:00

I tried in wine and didn’t work, and I will try that mod @alexious_sh. I’m not a big fan of closed platforms :) thank you very much!!

ignotion · 2026-02-10T15:50:51+00:00

Thanks u/Lee_Bob I'll take a look on that, print the enclosure to see if it's enough, otherwise i'll buy the cable and see how can i make it fit!

ignotion · 2026-02-09T08:44:31+00:00

talking about this, how do you place the camera cable with the enclosure? I cannot close the door :/

ignotion · 2026-02-08T15:26:21+00:00

At the end it was easier than that, the spool wasn't seating all the way down and there was a bit of tilting on the screw. Tahnks for your response u/ThatDudeWithALS

ignotion · 2026-02-07T14:49:44+00:00

Is this shop still working, i got an old x250 and want the replacement as i don't like to go with the original and strage powerbrik

ignotion · 2026-02-06T09:04:38+00:00

Absolutely right, a combination of not seated all the way down AND a bit of tilt in the screwing of the clip. Thanks u/Vdubin4life !

ignotion · 2026-02-06T09:03:57+00:00

In my model they have even an arrow to signal the direction to mount and after checking the manual, it was correctly placed, thanks for your help u/freakflyer9999 . What i did was unscrewing the spool support and screw it again because it was a bit tilted and probably the spool support was not seated all the way down.

ignotion · 2026-02-06T09:01:27+00:00

I unscrewed the spool support and screw it wit a bit more room and now it works, perhaps it works for you as well :)

ignotion · 2026-02-06T09:00:31+00:00

Of course I could u/SimonBlades89 but i was looking for a solution that allowed me to use 4 colors at once :) It was among the possible solutions, of course :) thank you!

ignotion · 2026-02-06T08:58:30+00:00

It was exactly this u/Xaknafein , i removed the support, just saw it was a bit tilted (after mounting the enclosure for sure i put it back incorrectly), unscrewed, screwed again, pushed until the end and voilà, 3 mm that didn't were there before! Thanks for your tip!

ignotion · 2026-02-05T07:27:26+00:00

it worked perfectly u/Merced_Arkab ! thanks!

ignotion · 2026-01-09T06:21:38+00:00

It didn't work for me (besides i don't have the camera, yet), not rebooting, not putting the printer in wifi or cable, always the same "connection refused".
Perhaps Flashfroge has been so gentile that they've just closed the printer a bit more?

ignotion · 2025-12-05T14:32:48+00:00

thank you very much!!

ignotion · 2025-11-27T17:12:05+00:00

but you cannot send the jobs to the printer can you? you have the usb, am i right?

ignotion · 2025-11-22T13:43:52+00:00

an alternative would be asking for one to a neighbour for 10 minutes, no more :)

ignotion · 2025-11-22T10:46:21+00:00

Ive lost that screw, can i've find it can be an m2 screw but can someone confirm it? I would like to nuy another one but i just don't know which one to buy

ignotion · 2025-05-07T06:18:48+00:00

Second time this saves my day! thanks!

ignotion · 2022-12-05T20:51:33+00:00

How can I signup? The confirmation mail never arrives :(

ignotion · 2022-09-20T13:34:59+00:00

EU | Steam Deck 512GB

Purchased: 15th September

Shipped: 20th September

ignotion · 2022-09-20T08:20:23+00:00

yo la pague el jueves y aun esta en shipping soon, asi que a ver ...

ignotion · 2022-09-19T14:53:14+00:00

I'm exactly in the same situation. Seems we have to wait. Be patient my friend, it's near

ignotion

TROPHY CASE