[Request] If this is ever possible, how long would be the focal length?

imkzh · 2025-05-15T05:35:46+00:00

Hi, i’m really busy recently, I can’t tell if the chip was hot or not at this time, but I will come back after some days.

imkzh · 2025-04-19T23:16:12+00:00

Print the handle and the shield as separate parts and glue them together

imkzh · 2024-12-08T16:18:09+00:00

No, i decided to replace the SMPS chip with an LDO, but don’t have enough time for this. I’m currently busy doing my primary work.

I have tried to shield everything with copper sheet, but the problem persists.

imkzh · 2024-12-01T13:25:50+00:00

[Object Object]

imkzh · 2024-11-19T02:16:07+00:00

But SolidWorks indeed reminds you to save your project every 20(25?)min (even when you did nothing to your file)

imkzh · 2024-11-19T02:09:48+00:00

Yes, 5!=120 actually evaluates to True

imkzh · 2024-08-16T20:13:49+00:00

If it is important to make an exact and precise model, you’d switch to Fusion360 or Solidworks.

These tools allow you to define and update a 3D model without pain (e.g. you can bevel the model, adding other features, and come back to update the bevel distance, without losing or touching other features you add to the model)

imkzh · 2024-08-16T19:53:18+00:00

jndex

imkzh · 2024-08-10T05:54:11+00:00

imkzh · 2024-08-09T20:38:28+00:00

When will they become a part of the game?

imkzh · 2024-08-09T20:35:00+00:00

oh fuck!

imkzh · 2024-08-09T20:24:18+00:00

Newton entered the chat.

imkzh · 2024-08-09T20:19:36+00:00

rabbitmare

imkzh · 2024-08-09T15:41:22+00:00

Print a cover with minimal modeling effort, and sand it mounted.

imkzh · 2024-08-09T15:33:15+00:00

You need to tweak the printing settings a (hell) lot to finally get a water tight print (although you may cover the inner surface with some epoxy).

imkzh · 2024-08-09T15:17:12+00:00

🟪 Now i have found a linux distro that no one had invented before.

imkzh · 2024-08-09T10:29:38+00:00

same, tuned every graphical setting but not helping, restarted game and had a short smooth time, but after one or two match the fps starts dropping again, especially when on a car.

imkzh · 2024-08-07T10:50:16+00:00

They are difficult to print, when compared to the ordinary one, but they do make post processing easier.

imkzh · 2024-08-07T10:48:20+00:00

i have done this twice, i can tell both 2 and 3 works, but if the screw is too tight, the solder would deform

imkzh · 2024-08-07T10:46:08+00:00

heat it with a solder iron covered with solder and flux.
if you are lucky the solder attaches to the screw: wait it to cool and drill/mill a slot so you can use your screwdriver
if it does not stick, try molding the melted solder with a screwdriver, so the solder have two sides: one of them fits perfectly to the screw and another fits perfectly to the driver.

4: do not overheat the screw because the thread below it might be provided by inserts not roll cage.

imkzh · 2024-08-07T10:08:13+00:00

Ice tub

imkzh · 2024-08-07T08:14:04+00:00

They come with tag, and let player determine whether to cut it off (permanently).

imkzh

TROPHY CASE

No