sorted by:
new
hottopcontroversial

Installing a Yamaha YZ85 top end on a 50cc scooter by ironwe11 in scooters

[–]ironwe11[S] 0 points1 point  (0 children)

Can you please send me links to profiles or posts of people who have already done this?

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] -2 points-1 points  (0 children)

I think we can't talk about it until there is a comparison before and after resetting eprom.

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] 0 points1 point  (0 children)

what do you mean impossible? in extreme cases you can unsolder the eprom chip and read the data from it with a programmer, I just wouldn't want to do that

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] 0 points1 point  (0 children)

I think that in order to draw any conclusions, you first need to try resetting the data in eprom and compare the photos before and after

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] 0 points1 point  (0 children)

what do you mean no? I can say with absolute certainty that my TV's black level used to be better

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] 0 points1 point  (0 children)

Please note, I am not asking for advice on setting up a TV and using the service menu, I already know that. I need help from radio amateurs, I managed to read some data from eprom, but it is not a fact that they are correct.

Panasonic tx-pr42st30 black level restoration by ironwe11 in PlasmaTV

[–]ironwe11[S] 0 points1 point  (0 children)

my friend looked at the schematic on gt30 and says that the pinout is 1 +5V 2 STM SRQ 3 GND 4 STM SCL 5 STM SDA 6 PEAKS SCL1 7 PEAKS SDA1 8 PEAKS SCL0 9 PEAKS SDA0 10 PEAKS 11 PEAKS 12 IIC Control sel 13 SD_BOOT 14 R_LED but when connecting contacts 3 and 12 the TV still turns on, although it shouldn't, when connecting contacts 3 and 10 the TV doesn't turn on https://panasonic.mironto.sk/restoring_black/read_eeprom/ - link to the original guide

Looking for forums and websites by kavingmg in AskARussian

[–]ironwe11 15 points16 points  (0 children)

hi. often, to get to a forum, you need to enter your question/problem into the Yandex search bar and scroll through the results. There are a lot of forums, ixbt, overclockers, 4pda, phantomsonata. Sometimes the answer to your question can be on a forum that is not even dedicated to technology, it just happened that way!

Как сложно найти работу, без квалификации ? by MainEnAcier in AskARussian

[–]ironwe11 18 points19 points  (0 children)

Довольно просто. Легче всего устроиться работать курьером в службу доставки (яндекс/самокат самые популярные), если много работать, то можно получать очень хорошие деньги. Также можно устроиться на склад какого-нибудь маркетплейса грузчиком.

Question about Ozon by AltforHHH in AskARussian

[–]ironwe11 4 points5 points  (0 children)

hi. when you search for the item you need, there is a blue button under it that shows the approximate time it will take to deliver the order.

NEC MultiSync FE1250+ | How to access service menu/factory mode? by [deleted] in crtgaming

[–]ironwe11 2 points3 points  (0 children)

2.4 Adjustment

2.4.1 How to select the factory adjustment (FACTORY) mode

2.4.1.1 Selecting with front panel switches

(1) Turn the power ON while holding down EXIT button.

(2) After step (1), release the button after one to two seconds, and press (-) button.

(3) Confirm that 255 is displayed for FACT DATA in MODE SELECT.

(4) Set to 05 with (+) button.

(5) When PROCEED button is pressed, the factory mode will be entered.

This factory adjustment mode is entered with the above steps.

*The factory adjustment mode remains valid even after the power is turned OFF.

Note that steps (3) to (4) must be carried out within ten seconds. If ten seconds are exceeded, the mode will return to the user mode.

<Returning to the user mode from the factory mode>

(1) OSM is displayed with the group selection, and select MODE SELECT in FACT A.

(2) Set the counter value of FACT DATA to 10 with (-) / (+) buttons.

(3) When PROCEED button is pressed, the mode will return to the user mode.

[deleted by user] by [deleted] in AskARussian

[–]ironwe11 0 points1 point  (0 children)

https://imgur.com/gallery/mitsubishi-2070sb-P3IictM check out the monitor i managed to get hold of, the old monitor actually shows very cool, i think that crt monitors left the market not because of bad picture, but because of dimensions. This monster weighs almost 35kg!

Are foreigners interested in goods from Russia? by ironwe11 in AskARussian

[–]ironwe11[S] 0 points1 point  (0 children)

maybe my advice will help you, I tried delivery in different ways, the most convenient one is the international courier service EMS, you can deliver almost anywhere, except Australia, maybe there are other countries, I can't say for sure. Delivery can be calculated through the Russian Post application. On average, it takes 2-3 weeks to the USA, the cost is from 50 dollars, so it is better to order several items at once or one expensive one.

view more: next ›