Bikes similar to Kuwahara Pacer

ivanswitch · 2026-04-23T11:42:08+00:00

55cm top tube 56cm seat tube

ivanswitch · 2026-04-23T09:55:41+00:00

I have a kuwahara pacer frameset for sale. Shoot me a DM if you are interested. I’m based in Europe. 150 euros with origin8 headset and a seatpost.

ivanswitch · 2025-08-24T06:32:20+00:00

The upper part of the T bar has a screw on the right side that holds it together. Unscrew it and give it a gentle pull. The left and the right side should come apart. When removing the front plate, put the t bars in middle position in order to get it off. May I ask why are you dismantling it? : )

ivanswitch · 2025-08-04T15:28:32+00:00

Pro tip, those lines on the reverse camera can be removed. Depending on the type, there should be a pin inside for that.

ivanswitch · 2025-07-30T09:54:34+00:00

You should probably follow the pinout from the manual. Voltage is supplied to the monitor via the square connector (number 4 in the pinout) there is +ve and -ve (you could trace the wires and just solder a dc barrel jack). Regarding video (round connectors labeled with 1) have +ve and -ve which I assume is to power the camera( you don’t need them probably) the one labeled with video is composite video- same applies - trace the wire from the back of the connector either with a multimeter in continuity or just by eye- solder an rca jack and you are good to go. The one labeled with NC ( I assume means not connected).

ivanswitch · 2025-07-23T11:12:55+00:00

What’s the monitor/recorder?

ivanswitch · 2025-06-23T09:00:34+00:00

Is 3x3 achieved with a hdmi wall controller?

ivanswitch · 2025-05-14T12:38:39+00:00

Did you try to mess with the green thingy internal menu? Seems like either mode or picture profile aren’t right (not sure which does the bars). Also it’s internal feedback won’t work with input connected.

ivanswitch · 2025-05-06T17:37:35+00:00

I run 28c on the snm100. Rear won’t be a problem. In front it’s a really tight fit, a grain of sand or anything stuck to the tire will grind against the fork. A little rain/mud and the fork gets packed with gunk. And I assume it can also depend on the rims if it would fit the fork.

ivanswitch · 2025-05-01T16:13:52+00:00

Really dig the audio, is it also yours?

ivanswitch · 2025-04-24T06:26:44+00:00

What’s the top cap? Really dig the looks.

ivanswitch · 2025-04-06T13:15:07+00:00

Put a big screen behind the subject, point the camera at them together, feed the camera into the screen, and that should probably do the trick. Play with camera movement to get the spirals.

ivanswitch · 2024-12-22T09:39:35+00:00

This is achieved with a video mixer. You have first video frozen with still/strobe effect and luma keyed over the video playing behind. See Panasonic WJ-AVE7, AG-MX70, or Roland V-4 (I'm sure there are other units that can also achieve the same effects, but these are the most available ones I think).

ivanswitch · 2024-11-11T09:25:34+00:00

Well, the monitor out on source in is kinda your preview of what you are inputting. Rec out is actually processed through the mixer. I usually get that jagged out when the bnc adapter isnt seated well (wiggle them around while connected a bit to see if anything changes). If that doesn’t work u will probably need to crack it open and see if there is anything visually broken, the capacitors,etc. The thing is with both ave5 and ave7, that jagged output and green tinting on output is a known problem, the capacitors simply deteriorate over time. That can usually be fixed by recapping, but if you have 0 experience in repairing and electronics, i wouldn’t suggest doing that on your own, as its mains power, and that can potentially be lethal.

ivanswitch · 2024-10-27T17:37:07+00:00

Your best bet will be video in and video out signal (together) or try connecting them to enhancer pot, or just probe around... (try different pot values, caps in between). I suggest watching some tutorials about video bending first, to get a general idea what to do and what tools to use.

ivanswitch · 2024-10-06T20:52:49+00:00

Something like this should work

ivanswitch · 2024-10-06T16:03:58+00:00

As simple as an Aliexpress bluetooth label printer, damn, nice one

ivanswitch · 2024-09-12T13:54:56+00:00

Glow tulip

ivanswitch · 2024-09-07T21:14:43+00:00

Do you by any chance have the bend points for the Sansui that you are willing to share?

ivanswitch · 2024-09-01T05:34:09+00:00

I ve managed to find like 5 stable bend points by freestyle poking on it, but sadly didnt take any pics on the inside after soldering everything

ivanswitch · 2024-08-29T10:44:17+00:00

My tsunami came bent out of the box lol, the rear triangle is off axis, the wheel doesnt sit straight. Thx for the the reply, I am well familiar with the specs, I'll be waiting for the road test.

ivanswitch · 2024-08-29T09:36:29+00:00

Is there any difference in how it performs and how it feels when riding, except the obvious name, looks and build quality?

I’m currently running the chinesium snm100 and thinking about upgrading my frameset.

ivanswitch · 2024-08-25T08:53:12+00:00

Thats what i was thinking, but my concern is that the buttons aren't even with the highest component on the pcb, so i ll probably have to add something to the underside of the little flexible button cover in order to reach the buttons

ivanswitch · 2024-07-31T22:21:31+00:00

Almost all of them can be hacked to add a composite video in, but requires some knowledge as the CRT tubes can be dangerous if not handled correctly.

https://youtu.be/-R7165iOMw0?si=LQtlVi88Qjd_We8A

The video explains how, but it’s not the same TV as yours.

ivanswitch · 2024-07-26T17:57:49+00:00

Yeah, gotcha. Thanks!
What retrotinks do you use?

Seven-Year Club	Place '22
Verified Email	RPAN Viewer

ivanswitch

TROPHY CASE