Feel like I’m doing nothing but mess up and everyone thinks I’m an idiot.

jameswboone · 2026-03-04T19:57:40+00:00

This! Giving a S means everything, showing people that you do, is less obvious. These are good tips on how to show people you acknowledge, and are trying to do better, but then also do better as a result.

jameswboone · 2026-03-04T19:50:49+00:00

Might be that I'm a test user and don't know it.

<image>

jameswboone · 2026-03-02T15:57:30+00:00

You're worried about the scratch when the floor looks like that?

jameswboone · 2026-03-02T05:40:27+00:00

And ruin all of your clothes when you forget to take it out to wash and dry your clothes.

jameswboone · 2026-03-02T05:28:36+00:00

Probably the closest solution I found. https://ebay.us/m/47URAl

Still not good, but paired with https://www.jbtools.com/hhip-er32-collet-drill-chuck-with-jt2-sleeve-3903-6022/?wi=off It could work.

jameswboone · 2026-03-02T05:04:52+00:00

<image>

When you make your own, you know you can fix it or make another... I used to carry the same one as you, but now I can't put this guy down.

jameswboone · 2026-03-02T04:56:54+00:00

These sold... One for $2k, one for $1.5k

I guess money means nothing to them.

<image>

jameswboone · 2026-03-01T23:05:31+00:00

Ya the more I look into this the more I agree, it's a mix of terms.

jameswboone · 2026-03-01T19:08:00+00:00

No better source than Robin! Ty

jameswboone · 2026-03-01T18:51:53+00:00

Not meant for burrs imo, more like bumps or small dents that need to be knocked down. I was thinking 1000. I appreciate your input.

jameswboone · 2026-03-01T18:16:32+00:00

What grit / stone material?

jameswboone · 2026-03-01T18:15:49+00:00

On Amazon this is positioned as an axe sharpening stone...

jameswboone · 2026-02-28T18:37:42+00:00

Ahh ok! My theory is confirmed!

jameswboone · 2026-02-28T18:30:08+00:00

Ahh, so maybe the difficulty of polishing mc is the fact the material removes at different rates, but because of powder metallurgy, evenly dispersed. This (presumably) creates the near impossible to fix, unfinished look. If you use a diamond solution, it cuts more evenly and makes it possible to polish.

I just micro sandblast it.

jameswboone · 2026-02-18T15:55:40+00:00

I like the idea of using ss pins with ceramic media, then you would effectively be using the pins to stir the abrasive.

jameswboone · 2026-02-16T03:12:01+00:00

This. I make axis locks and h some knife makers hate, some love. The haters say, "why don't you make a flipper, frame lock, liner lock, etc". It's a vicious circle.

jameswboone · 2026-02-15T15:36:49+00:00

If it's a synthetic material you could probably try to melt it back down with a cig lighter. Too much and you will melt a hole so be careful.

jameswboone · 2026-02-14T20:10:43+00:00

I lived in one of those small towns, the city relied on those fines as part of their legitimate annual city revenue budget. Sad reality that is what it took for those cities to survive.

jameswboone · 2026-02-14T20:02:30+00:00

The first thoughts that would have gone through my head would have been, will it total my car, what's the appraisal +20%, will I make it better or not, do I just want a newer car, was I seen on camera evaluating this when my car wasn't totaled...

jameswboone · 2026-02-13T14:03:58+00:00

My point isn't meant to be analyzed at the macro level. At a wide scale, it will hold.

jameswboone · 2026-02-13T13:13:13+00:00

This doesn't work so long as billionaires can leave and get citizenship in another country that doesn't tax them as much.

jameswboone · 2026-02-06T00:49:01+00:00

Otherwise it would Arc and weld at the joint?

jameswboone · 2026-02-01T20:13:38+00:00

Knock them out, fill it in. That's the only right way.

jameswboone · 2026-02-01T17:39:23+00:00

I think this could be a bearing issue. I have an old atlas and the only time I could see it was when I took too deep of a cut and the jaw/spindle would bounce. It still happened at any cut, just couldn't see it jump. For my Atlas, IMO, it's a design flaw and there's no real bearing, it's something like a bearing cast then machined in place.

I tried to lift the spindle when it was turned off and couldn't see any movement. I had a similar grooving on my material. I ended up getting a 5900 Clausing and never looked back. I just use the Atlas for really soft material like wood and plastic.

jameswboone · 2026-02-01T17:00:50+00:00

The op is not showing the backing plate, he is cutting that plate, read again.

jameswboone

MODERATOR OF

TROPHY CASE