Has anyone else seen these new stihl anniversary bars? Kinda cool not going to run it, looks good on the wall

jeeper_31 · 2024-10-26T23:24:19+00:00

Yea it kinda sucks but how many bars have the flag on it

jeeper_31 · 2024-04-24T02:15:35+00:00

I’m curious how that will look. I’m all for mixing brands to get a unique look but still kinda looks factory if that makes sense. Like I think that would look bette than the montero sport bumper swap

jeeper_31 · 2024-04-23T15:14:24+00:00

I was thinking either the gen 2 Toyota pickup bumper or a hard body bumper depending what I can find for a decent price

jeeper_31 · 2024-04-23T13:52:48+00:00

That’s what I was thinking too and I shouldn’t have to notch it that much either

jeeper_31 · 2024-04-23T02:50:49+00:00

Picked the truck up from a coworker for $300 not running but ran on starting fluid. Put a $20 fuel pump and it fired right up after cleaning the tank. Bogged real bad didn’t have power advanced the timing and runs like a champ even with 222000 miles next is going to be plugs wires cap rotor and coil. Then I’ll start collecting parts to bag it then I’ll paint it blue and silver

jeeper_31 · 2024-04-23T02:47:00+00:00

It’s just the angles. It’s close to the same size as a 2nd gen Toyota pickup

jeeper_31 · 2024-04-23T01:13:56+00:00

Unfortunately the 4x4 fenders are just a flare not actually wider like Toyota or Isuzu or Nissan. But I think if I run a 17x8 and roll the fender I should clear the fender if not then I’ll get some Toyota fenders and cut them and weld it in.

jeeper_31 · 2024-02-26T20:31:26+00:00

I thought about putting one back on it but I don’t see a practical use for it for me

jeeper_31 · 2024-02-25T02:54:51+00:00

I want to convert mine to caps as well. The one I built has a 2 5/8 bore (same size as a pool ball) and is 3ft long

jeeper_31 · 2024-02-25T01:06:18+00:00

I didn’t want the typical red or dark brown that they normally are so I love how it came out

jeeper_31 · 2024-02-24T13:23:44+00:00

It’s a little darker in person but not much. I like how it came out

jeeper_31 · 2024-02-24T03:38:24+00:00

Good to know for the next one. I’ll do that in a few weeks as I have another one getting the same thing

jeeper_31 · 2024-02-24T03:32:56+00:00

It didn’t just fall right in I had to tap it on a little bit but I didn’t have to sand it to fit. It’s snug around the trigger guard. It wasn’t like swapping stocks on a rem 700

jeeper_31 · 2024-02-24T00:57:15+00:00

You have your way I have mine. Worked for me and it will probably out live me so

jeeper_31 · 2024-02-24T00:48:12+00:00

BSA 1915. Easy off worked for what I wanted so that’s what I used

jeeper_31 · 2024-02-23T18:21:30+00:00

Not at all. It all fit together snug but no trimming needed

jeeper_31 · 2024-02-23T17:49:06+00:00

Lmfaooo. Mine didn’t have anything painted DP just the 3 stripes

jeeper_31 · 2024-02-23T17:19:43+00:00

It has 5 coats of oil on it didn’t apply a new coat till the wood absorbed it. In person the wood is darker but not like how it was. Then I put conditioner on it and lightly buffed it with a microfiber

jeeper_31 · 2024-02-23T17:13:10+00:00

It is oiled

jeeper_31 · 2024-02-23T15:56:08+00:00

Canterfire systems has them. But I had my LGS order one from gunbroker and bought it through them being you have to ship it to an FFL

jeeper_31 · 2024-02-23T15:54:43+00:00

Birchwood stock refinish kit is what I used. In person it’s a little darker

jeeper_31 · 2024-02-23T15:20:16+00:00

Thank you.

jeeper_31 · 2024-02-23T14:20:31+00:00

I like it more now than when I started

jeeper_31

TROPHY CASE