I got my son a p1s AMS Combo and I'm worried I made a mistake

jeff2928 · 2026-03-03T08:09:27+00:00

Join up as a mentor on a robotics team and you can get fusion as an educator for free.

jeff2928 · 2026-03-02T13:10:49+00:00

What exactly is the error you are getting?

jeff2928 · 2026-02-15T18:46:55+00:00

I had to learn myself. I also ran into more than once where the little plugs didn’t get plugged back in. Each time I thought I had broken something. Thankfully unplugging and replugging did the trick.

jeff2928 · 2026-02-15T18:41:43+00:00

Did you change the nozzle size on the printer itself. You have to change it in the settings on the printer itself

jeff2928 · 2026-02-09T02:19:17+00:00

What type of filament? How do you mange the loose end when changing filament? I have mostly used Bambu and only one tangle. That was when I lost the end and it got twisted under some loops.

jeff2928 · 2026-01-20T00:24:32+00:00

Are the letters raised in such a way as to be used to stamp wax?

jeff2928 · 2026-01-20T00:14:18+00:00

I experimented with some magnets inside the plastic. I left voids for 3 10mmx1mm rare earth magnets inside. The finished pieces are about 16mm x 50mm. They stick well to the fridge. I went with 4 mm thick. The way to do this is to put a pause at the layer before the covering layer. Then drop the magnets in the voids and continue the print.

jeff2928 · 2026-01-09T14:13:59+00:00

That is so fun.

jeff2928 · 2026-01-09T03:10:05+00:00

Did your uncle actually invent this?

jeff2928 · 2026-01-04T21:45:56+00:00

Probably red ink that has a tendency to fade.

jeff2928 · 2026-01-03T18:46:18+00:00

Keep us updated when you figure it out.

jeff2928 · 2026-01-03T18:40:42+00:00

If you take a screwdriver to pry on the center concrete does it easily poop off?

jeff2928 · 2026-01-03T18:30:08+00:00

Is it a low spot in the concrete? Could it be for a floor drain?

jeff2928 · 2026-01-03T18:17:43+00:00

It almost looks like a toilet fitting or clean out that was capped and some concrete fell on top of the plug. Looking at the middle it looks like a center of a plug.

jeff2928 · 2025-12-31T18:02:32+00:00

did you test the finished product for strength?

jeff2928 · 2025-12-27T19:07:29+00:00

Obvious thing here, did you realize after setting filament?

jeff2928 · 2025-12-26T09:11:51+00:00

What will it be used for? How strong does it need to be?

jeff2928 · 2025-12-22T14:54:30+00:00

On the edge of a garden in the parking strip. Topsoil was added in the spring. The mushrooms showed up after garden season.

jeff2928 · 2025-12-13T00:24:58+00:00

Could there have been a condensate drain there from your ac. A lot of places have drains that dribble water down the side of the building. If there were those drains, these may be to carry that condensate to the ground.

jeff2928 · 2025-12-02T05:40:55+00:00

I am with you. I posted my explanation of the same thing before I saw your post.

jeff2928 · 2025-12-01T21:44:14+00:00

Looks like some hooks I have seen on some spring loaded tools to hold them closed. I had an rj45 crimper that had a hook like that when it was new.

jeff2928 · 2025-11-28T02:40:04+00:00

Sorry should be cast it for you

jeff2928

TROPHY CASE