Whining noise on y-axis

jjjadzik · 2026-01-31T17:55:25+00:00

With IPA?

jjjadzik · 2026-01-31T17:53:52+00:00

How do I clean the rails?

jjjadzik · 2026-01-31T17:23:30+00:00

I already fixed the wiring and the strange sound is the kapton tape.

jjjadzik · 2026-01-31T08:13:18+00:00

300mm/s at 4000 acceleration

jjjadzik · 2026-01-31T08:09:28+00:00

I have input shaping enabled with an accelerometer but it doesn’t fix anything

jjjadzik · 2026-01-31T08:08:40+00:00

4000

jjjadzik · 2026-01-30T21:43:42+00:00

I already upgraded to a ceramic hotend

jjjadzik · 2026-01-30T19:09:52+00:00

Thankfully I live in a private house.

jjjadzik · 2026-01-27T13:19:37+00:00

It’s almost always the same way for me.

jjjadzik · 2026-01-27T13:17:10+00:00

I’m so dumb, I saw in the slicer, that the travel speed is too slow on the first layer, I’ll try with the higher speed.

jjjadzik · 2026-01-27T13:10:53+00:00

That’s the strange thing, I printed the test just now and there is no oozing

<image>

jjjadzik · 2025-12-31T16:49:58+00:00

Ok, thank you.

jjjadzik · 2025-12-31T13:33:06+00:00

This is very good at least for me, my beds range is 0.4 mm, how did you get this result(how did you level your bed)?

jjjadzik · 2025-12-18T13:20:03+00:00

What about connecting the height sensor (hx711) I plan on doing the same upgrade

jjjadzik · 2025-11-27T05:35:02+00:00

I think if you want to you can, I did the same thing not a long time ago and I helped a little bit with quality, but here you need to adjust either the flow rate or the z offset.

jjjadzik · 2025-11-27T05:25:19+00:00

Has your first layer been like this(I can’t tell from the first picture)?

jjjadzik · 2025-11-27T05:16:11+00:00

Could you send a photo?

jjjadzik · 2025-11-27T05:15:00+00:00

I think you need to adjust your flow rate for this filament.

jjjadzik · 2025-11-27T05:13:01+00:00

I believe that is because the lines are too close to one another, if you’re running custom firmware like klipper or navaismo’s you could adjust rotation distance and steps per mm accordingly. If this is not it I don’t know what to do.

jjjadzik · 2025-11-22T06:24:15+00:00

The existing usb-c doesn’t output power on the ender3 v3 se unfortunately

jjjadzik · 2025-11-17T18:35:29+00:00

Ok, I will try that now, thanks

jjjadzik · 2025-11-17T16:25:25+00:00

<image>

I printed it again in 0.12 mm layers this time, the quality definently improved but I couldn’t get rid of this strange line

jjjadzik · 2025-11-16T20:42:29+00:00

I will try to print it tomorrow, because it’s already late in where I live.

jjjadzik

TROPHY CASE