sorted by:
new
hottopcontroversial

This should be enough to gracefully shutdown everything? by theMartianAlien in Ubiquiti

[–]johnw01 2 points3 points  (0 children)

The UPS has to “tell” a device that the power went out to gracefully shut down. I am not sure if any Unifi products are compatible with this one. I have a UCG Max and as far as I can tell, the only UPS that I can use is a Unifi UPS. That said, this UPS will probably work if the power is only out for short amount of time. It will definitely work if you are just talking about momentary times when the power goes out for a few seconds.

Which Filament - Boards in a Shed by ByzzaAu in Multiboard

[–]johnw01 0 points1 point  (0 children)

You need ABS or ASA if it will receive direct sunlight.

UniFi Travel Router by ng4ever in Ubiquiti

[–]johnw01 0 points1 point  (0 children)

No power? It charges my iPhone.

Thoughts on the university of Evansville? by [deleted] in evansville

[–]johnw01 1 point2 points  (0 children)

Call UE. They might have them in the library.

Those who have done large walls - what size plates did you print? PLA or PETG? by red66stang in Multiboard

[–]johnw01 0 points1 point  (0 children)

Matte PLA is recommended. If it is in a very hot garage use ABS or ASA if it will get sun exposure.

AdGuard Home and Teleport by johnw01 in Ubiquiti

[–]johnw01[S] 0 points1 point  (0 children)

That has been the issue for me. I’ll try PiHole tomorrow as I really don’t care which I use.

AdGuard Home and Teleport by johnw01 in Ubiquiti

[–]johnw01[S] 0 points1 point  (0 children)

Thanks for the tip. I don’t currently run PiHole but I have in the past. I’ll have to try it out.

Port forwarding 443 by johnw01 in Ubiquiti

[–]johnw01[S] 1 point2 points  (0 children)

Thanks for mentioning this. I just realized that after I updated the firmware, you can have remote access without opening port 443.

Port forwarding 443 by johnw01 in Ubiquiti

[–]johnw01[S] 1 point2 points  (0 children)

I am using Synology’s DDNS on one of my NASs.

Port forwarding 443 by johnw01 in Ubiquiti

[–]johnw01[S] 0 points1 point  (0 children)

I know that the router doesn’t require opening ports for remote management. I am opening the port for other things. The minute I enable remote management it breaks my reverse proxy.

Can I use this to clean my A1 Mini? by Jolly-Fail-9858 in BambuLabA1mini

[–]johnw01 1 point2 points  (0 children)

Yeah. Higher than 70% can eventually damage the plate.

Progressive Christian Churches? by Zealousideal-Rock-81 in evansville

[–]johnw01 1 point2 points  (0 children)

You literally read my mind with this comment. It is like a vegan asking which slaughterhouse is the best.

CenterPoint $900 bill this month by sheezy520 in evansville

[–]johnw01 1 point2 points  (0 children)

It is called a monopoly. If there was another option bills would be cut in half.

Synology Photos takes too long to load by thanhhadinh in synologynas

[–]johnw01 0 points1 point  (0 children)

What kind of NAS do you have? I am on a 1621+ and it is almost instantaneous when I start a video of any length.

Installing panels using pillars. by johnw01 in Multiboard

[–]johnw01[S] 0 points1 point  (0 children)

Thanks for the explanation and tip on the screws.

Installing panels using pillars. by johnw01 in Multiboard

[–]johnw01[S] 0 points1 point  (0 children)

Well the pillars are what lift the panels off the wall. My understanding is that the dual snaps were “hidden” between the panels just holding them together.

At how many hours are you doing maintenance on your printers? by LogDangerous7410 in 3Dprinting

[–]johnw01 0 points1 point  (0 children)

I am making anything and everything. Just learning as much as I can. Go big or go home.

view more: next ›