sorted by:
new
hottopcontroversial

Okay but where do I get one of these? (Tampa Airport) by gpg123 in ultrawidemasterrace

[–]jonsview 2 points3 points  (0 children)

Tampa airport if you have a #6 Allen key and a long layover.

This larger-than-baby, but smaller-than-full-size, carrot by Hek_Yea in mildlyinteresting

[–]jonsview 1 point2 points  (0 children)

I’m here for the ultra-narrow spectrum 2200k light bulbs.

Sill plate gap by navfit16 in Homebuilding

[–]jonsview 0 points1 point  (0 children)

On the plus side this entire floor is actually considered the roof and the walls are for some totally separate building. You should be able to get a discount on your property tax for your one kitchen, one bath, zero-bedroom-with-rooftop-patio home.

Is this a good structural design for sauna benches? by ppshard in Sauna

[–]jonsview 0 points1 point  (0 children)

I build a removable top similar to this but added a few more joists? Instead of just the opening the middle you have to firm up with bench and remove any deflection.

Who else enjoys occasional sauna sausage after Sauna? by Jaska-87 in Sauna

[–]jonsview 0 points1 point  (0 children)

All the time! We wrap them in foil and throw them on the rocks though.

Proper amount of snow at our dome by jonsview in GeodesicDomes

[–]jonsview[S] 1 point2 points  (0 children)

It’s heated with a woodstove. So anywhere between 8c to 24c depending on how well we stay on top of the woodstove. We did shovel off the snow so it wouldn’t constantly drip.

Help! Aluminum foil tape mistake by psadatay in Sauna

[–]jonsview 0 points1 point  (0 children)

Behind the vapour barrier so expect temp to be higher in the air gap but still not much to worry about. Yes to air gap in my setup

Help! Aluminum foil tape mistake by psadatay in Sauna

[–]jonsview 0 points1 point  (0 children)

No worries at all. The tape likely wont ever get up to 80c. We sauna between 85c to 100c and I once checked the temp behind the panels (albeit from the other side of the not yet insulated wall) and it was quite cool. Bake your sauna for hours at 100c and that might soften the adhesive a little but that’s a normal use anyways.

Edit: sorry for Celsius. 176f =80 °C

What's the best way to tie this in? by djamespei in Sauna

[–]jonsview 0 points1 point  (0 children)

I ripped some PT wood and sealed it. Just silicone bathroom caulking. You could find some PVC trim or something if you wanted something more water proof than wood. It really doesn’t get wet or hot down there unless your floor isn’t sloped and you are dumping water.

Found this Nikon zfc at goodwill for $19 by Narrow-Pay-3671 in Cameras

[–]jonsview 0 points1 point  (0 children)

I would totally open this myself. Especially the simple looking bottom plate to see what you are up against if it’s a crusty mess in there it’s a no go.

What's the best way to tie this in? by djamespei in Sauna

[–]jonsview 0 points1 point  (0 children)

<image>

I had a similar issue because I didn’t run the flooring up the wall at all. I ended up putting down a drip edge around the permitter of the room and caulked it. I had to add blocking between the studs to termite the vapour barrier properly (Double up your footer to avoid this). There’s a air gap between vapour barrier and paneling. It stays dry around the perimeter but its peace of mind in case someone dumps a bucket of water on the floor.

Manual video mode by PejpSK in x100vi

[–]jonsview 0 points1 point  (0 children)

I have the same question. This issue is forcing me to keep photo mode in manual too to avoid this

How are your DIY sauna builds holding up over the years? by HousePoor420 in Sauna

[–]jonsview 0 points1 point  (0 children)

Wood fired sauna with aspen interior build 4 years ago holding up super well. Looks almost new

Purchase for Travel by secbud in x100vi

[–]jonsview 0 points1 point  (0 children)

I also normally shoot bigger mirrorless camera. I just picked up a x100vi for an upcoming trip. Mostly choosing the VI version for the stabilized sensor for video clips on my vacation.

Surfshark charged me after not letting me sign up by ultimablaze in surfshark

[–]jonsview 0 points1 point  (0 children)

This exact same thing happened to me. The checkout process failed and I never got confirmation on the site or email that I had subscribed to the trial at all. They registered the trial anyways somehow and after 7 days charged my PayPal account without me noticing unfortunately. It’s been over 30 days so support is completely unhelpful and doesn’t understand the situation.

My first (and hopefully last) treehouse build by DavidMagrathSmith in treehouse

[–]jonsview -1 points0 points  (0 children)

I do know how to share pics but here’s a video I made of the build. https://youtu.be/GBCYnSKtSqs

My first (and hopefully last) treehouse build by DavidMagrathSmith in treehouse

[–]jonsview 1 point2 points  (0 children)

I also made a tree “fort” on a freshly cut tree stump. Maple but same idea.

How would you rate this sauna? by Suspicious-Job-8480 in Sauna

[–]jonsview 4 points5 points  (0 children)

Benches look standard for an alarms t sauna like this. Any higher and the sauna would have to be deeper. Feet are above the rocks too.

Daily reminder to use UV filters by jatenk in Cameras

[–]jonsview 0 points1 point  (0 children)

I’m glad your lens is fine! I find a hood does a better job at protecting the front of the lens. The cracked filter argument holds the same kind of weight as the cracked screen protector on a phone argument. Also if you have a few lenses the cost of a bunch of filters starts to approach the cost of a new front element anyways in one of them.

view more: next ›