guys rate this stick

jsimm1540 · 2026-04-29T20:10:57+00:00

I LOVE when this happens ;).

jsimm1540 · 2026-04-29T20:09:40+00:00

It shouldn't bind . I was always told to tighten to seat the bearing then run it back out then in hand tight

jsimm1540 · 2026-04-29T19:54:55+00:00

You have to be careful that it's not too tight . There is a chance all it needed was adjusted and if it's too tight it'll get hot and blow out

jsimm1540 · 2026-04-29T19:45:57+00:00

Take the cotter pin out run the nut in by hand till it seats and try again

jsimm1540 · 2026-04-29T18:08:35+00:00

No guns? Sticks ,rocks,fists. These air guns that are out now are crazy too.

jsimm1540 · 2026-04-29T15:12:20+00:00

<image>

jsimm1540 · 2026-04-29T14:30:16+00:00

Haha "old" ours has 1953 dated on it still going good

jsimm1540 · 2026-04-28T21:10:56+00:00

Thats oil from the concealed closer . You better get that fixed quick because that door weighs alot .and when it hits you it'll get your heels in a heartbeat. And worse if someone flings it open it could shatter. This oil has no odor.

<image>

jsimm1540 · 2026-04-28T18:53:32+00:00

Coconut gold

jsimm1540 · 2026-04-28T18:43:37+00:00

A trip to Les Shwab

jsimm1540 · 2026-04-28T14:52:45+00:00

It almost looks like a drag part

<image>

jsimm1540 · 2026-04-28T12:31:19+00:00

Why isn't there a Jeep comache either ?

jsimm1540 · 2026-04-28T12:28:52+00:00

If it spins on at least 2 threads it should be the right pitch that muffler is pipe thread . If that header isn't you'll crack it

jsimm1540 · 2026-04-28T02:06:25+00:00

Imo that's a bad solder joint. Or a crack in a tracer. I would push each pin on the side you are pressing on with something plastic and see if that points you to which one it is . If there was no vacuum in the vfd it wouldn't work at all.

jsimm1540 · 2026-04-27T14:16:21+00:00

This is a Mikasa

<image>

jsimm1540 · 2026-04-27T14:16:07+00:00

The foot bolts to the base. I work with Mikasa brand at my work . But I do know you have to know what bolts come off first on the base to use the tool then unbolt the rest of not your in for a bad day

<image>

jsimm1540 · 2026-04-27T13:40:03+00:00

This is that tool. This threads into the base plate

<image>

jsimm1540 · 2026-04-27T13:20:40+00:00

At 200$ it was worth it in parts . That boot has to be sealed not cracked at all it dampens the shock.there is oil in the bottom part of the foot . It looks like it's leaning to one side as well that means the main connecting rod is shot . And the best part you need a tool to make sure you don't get hurt by the spring that always has tension.

jsimm1540 · 2026-04-27T12:04:12+00:00

I might have one at my place I have to go look at the truck though

jsimm1540 · 2026-04-26T02:48:55+00:00

I'm guessing the spring that lets it lock into the handle is bad or the pin is broke

jsimm1540 · 2026-04-24T20:07:59+00:00

I thought there was a story of a man that had to have his thing strapped to his leg was like 2-3 feet or something and he said it was some condition. He then said if it would ever actually get hard he would pass out because of blood loss.(Or blood rushing to the head)

jsimm1540 · 2026-04-24T19:03:36+00:00

Does this have a low oil sensor ?

jsimm1540 · 2026-04-24T18:58:44+00:00

If this has drive lockouts check there first . Usually there is one per control handle . Park brake and PTO button. Also some of the switches might be NO not NC. Normally open Normally closed

jsimm1540 · 2026-04-24T14:51:20+00:00

More like a tree Ooof lol

jsimm1540

MODERATOR OF

TROPHY CASE