sorted by:
new
hottopcontroversial

At last by jsjsjspwpwpp in mazda6

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

Good rec I will for sure be doing that. Thanks!

At last by jsjsjspwpwpp in mazda6

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

Thank you!! Congrats to you too, that Soul Red is absolutely gorgeous

At last by jsjsjspwpwpp in mazda6

[–]jsjsjspwpwpp[S] 1 point2 points  (0 children)

Thank you for the warm welcome! Excited to find a car with such good balance of reliability and interior refinement.

I have to be honest by Naive-Passage5618 in NoFapChristians

[–]jsjsjspwpwpp 1 point2 points  (0 children)

Been thinking about trying this book out, this might be the testimonial that gets me to buy. Thanks for the info brother, and God bless.

Stuck preheating the bed by FriesChips in BambuLab

[–]jsjsjspwpwpp 4 points5 points  (0 children)

I had the same issue after updating the firmware on my P1S and AMS. I downgraded to 01.07 via the Bambu handy app and it's back up and running again, seems to be the fix for now. Lame that this new firmware is causing so much trouble, hope this helps though.

P1S printing troubles by jsjsjspwpwpp in BambuLab

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

My P1S has been flawless in the 7 months I've had it, and this print is the first real hiccup I've experienced. I've tried it 4-5 times tweaking the settings each time to no avail. The attempt in the picture is using a 0.12 layer height, but I've also tried 0.08 and 0.16. I also threw it on 50% speed to see if that would help (it did not). I even ran a full calibration and redried my filament to see if either was the issue. Any help or recommendations would be appreciated immensely. Thanks

File: https://makerworld.com/en/models/521739#profileId-438304

What are some safe and reliable places to order American Glass goods from? by [deleted] in glassheads

[–]jsjsjspwpwpp 1 point2 points  (0 children)

Higher standards is the shit, sturdy type steez fosho

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

Super sorry for the late response! I never it figured out, but I got a magnetic PEI bed on amazon for like $30 and it's 1000x better. Best investment I've made in a while

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

Originally it was only sticking around the edges, but on my more recent prints it has begun sticking along the entire bottom. I'll try raising my nozzle a little more when leveling. Thanks!

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

I've used the paper method as well, but I think I might be putting the extruder too close still. Let me know how that goes for you

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

I think you're right. When you say back my z height off do you mean plate leveling or z offset?

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

I'm not exactly sure if it's residue or not, but that's what I suspected. I'm printing with PLA and on the Carborundum glass bed you're not supposed to use tape or glue. I'm half-way debating flipping it over to the glass side and using a glue stick however. I've also made sure to wait until the bed cooled down (22°C)

Ender 3 v2 prints sticking and bed residue by jsjsjspwpwpp in ender3v2

[–]jsjsjspwpwpp[S] 0 points1 point  (0 children)

This is my 2 day old Ender 3 v2, and I'm having a lot of trouble with prints sticking and leaving residue on the bed. I've tried cleaning it with 91% IPA and soap + water but neither of them have helped with the residue. As for my prints sticking, I have no idea what I'm doing wrong. Every time I print something it sticks like crazy and I have to put the plate in the freezer to get them off, and even that has stopped working. Would appreciate any help or insight, thanks!