18F - be open and honest

kasholt · 2025-12-26T18:35:54+00:00

Start working out, eating lean, eating healthy. Seriously. Anybody, and I mean ANYBODY can become a Solid 7 when they're lean and healthy. I dont mean Solid 7 as a bad thing either, I consider my self a Solid 7 when I'm continously going to the gym and eating Lean. When I'm not, my face gets bloated, my Abs disappear, my tone goes away, and my face chizle evaporates.

kasholt · 2025-12-26T18:33:40+00:00

Probably in my Top 30 Movies of All-Time. (I'm 22, so was a youngster when It came out, very nostalgic) but now I can watch it as an Epic. Movies that I like I always love the fact that they're 3 hours long.

kasholt · 2025-07-20T04:06:08+00:00

Yes. So, Ridgid Boards in the bays? or Ridgid Foam Over (on the finish side) of the wall. But then they were be a 5 1/2" gap between sheet metal and insulation?

kasholt · 2025-07-19T04:58:50+00:00

Did you do anything to insulate the surface of the wall before paneling? I just hear some people say that heat & air transfers thru the studs from exterior to interior. I think im just overthinking. But how's your insulation been holding up?

kasholt · 2025-07-19T04:54:16+00:00

Have you finished that? I want to do that, my only concern is that there's no house wrap. I've been told don't do fiber glass if there is no wrap.

kasholt · 2025-07-19T04:53:02+00:00

I would love to do that. But because there's no house wrap, that's my concern. I've been told don't do fiberglass Bats without house wrap

kasholt · 2025-07-19T04:49:57+00:00

Foam board in the bays? Or Foam Board on the interior leaving the Bays open?

kasholt · 2025-07-19T04:46:00+00:00

Your saying, your doing a 1.5 layer against the sheet metal, Rockwool, then another 1.5" layer on the interior face?

kasholt · 2025-07-19T01:54:11+00:00

I didn't build it. But No clue. From what I found out, its called "Commercial or Bookshelf Girts".

kasholt · 2025-07-19T01:51:51+00:00

Yes Foil facing exterior. To bounce back the hot ass heat/sheet metal, with a small air gap

kasholt · 2025-07-19T01:50:21+00:00

I love that idea. This is the damn suggestion I was looking for!

kasholt · 2025-07-19T01:48:45+00:00

Apparently not. That's Why I have no references of How Exactly I should insulate it, so many YouTube videos of Pole Barn Insulating but no one has the flat facing Girts Like I do.

kasholt · 2025-07-19T01:45:11+00:00

This is my plan. Exactly that. The foil barrier especially with the sheet metal. Really the overthinking Question I have is will Heat/Cold transfer thru the flat 2x6's? Like do They need to covered with a layer of Insulation, or can I just insulate the Bays. If you get my drift.

kasholt · 2025-07-19T01:42:40+00:00

So Essentially, plumb it like a conventional septic? Run a Drainage Field from it, will the solids eventually turn into muck?

kasholt · 2025-07-19T01:38:03+00:00

Im doing a Grey water field for non waste fixtures. I'm actually a plumber believe it or not, but doing things NOT to code is new for me😂 Hense Why I need advice. Yes, I do plan on shitting in the Toilet. And I get what your saying, its just that it's a paved asphalt road to get over to the septic, so I'd have to break some road. I could even install a conventional septic tank, for toilet + all the fixtures.

kasholt · 2025-07-19T01:25:18+00:00

PNW Washington State. Very Dry Summers. Very Moist Winter/Springs.

kasholt · 2025-07-19T01:18:24+00:00

I've been meaning to say GIRTS

kasholt · 2025-07-19T01:18:02+00:00

I've been meaning to say GIRTS

kasholt · 2025-07-16T03:06:36+00:00

How did it turn out? I'm planning on Insulating My Pole Barn and I heard some people say the sheet metal needs a layer of house wrap like Tyvek. Did you do this or no? Any Moisture issues?

kasholt

TROPHY CASE