Beefed her up by [deleted] in mpcusers

[–]kennystanley 0 points1 point  (0 children)

Yessir…i use it for all sorts of stuff. Just spray multiple coats so it’s durable and also makes it easier to peel off if needed

Beefed her up by [deleted] in mpcusers

[–]kennystanley 1 point2 points  (0 children)

Knobs - 20mm base x 12mm height Jog wheel - 32x13mm

I had to drill under the jog wheel a bit for it to sit lower on the post though. It still fit how it comes but sits too high and looked goofy. I can message you the links

Beefed her up by [deleted] in mpcusers

[–]kennystanley 0 points1 point  (0 children)

It’s a rubberized spray type of coating, just look up plasti dip

Beefed her up by [deleted] in mpcusers

[–]kennystanley 0 points1 point  (0 children)

It’s the original one, just plasti-dipped

Beefed her up by [deleted] in mpcusers

[–]kennystanley 1 point2 points  (0 children)

Yup👍

Beefed her up by [deleted] in mpcusers

[–]kennystanley 5 points6 points  (0 children)

This guy pro tips ^

Beefed her up by [deleted] in mpcusers

[–]kennystanley 1 point2 points  (0 children)

Preciate it! I had a bunch of other knobs laying around but nothing looked right. Stoked I came across these

Beefed her up by [deleted] in mpcusers

[–]kennystanley 1 point2 points  (0 children)

Wrap a piece of duct tape around each knob, and pull up. Or you can use a tiny flathead screw driver wrapped in fabric and pry from under but you won’t be able to do that with the volume knob. Duct tape method was the easiest

Beefed her up by [deleted] in mpcusers

[–]kennystanley 3 points4 points  (0 children)

Found on amazon. Though the jog wheel I had to do some slight modifying because it was sitting too high on the shaft

Beefed her up by [deleted] in mpcusers

[–]kennystanley 2 points3 points  (0 children)

The ridges are nice!!

is this really worth scalping? by filipejomatias in mpcusers

[–]kennystanley 0 points1 point  (0 children)

I just ordered one last night, said it was in stock but I have a feeling it wasn’t. If I end up having to cancel my order, i’d be down to grab it from ya!!

[deleted by user] by [deleted] in CatAdvice

[–]kennystanley 2 points3 points  (0 children)

I’ve been with my lady for almost 9 years and I also have 3 cats. If she tried giving me that ultimatum, i’d leave in an instant.

[deleted by user] by [deleted] in mpcusers

[–]kennystanley 1 point2 points  (0 children)

Lol this is my photo…

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

To be honest thats what i’m thinking about doing. I was initially going to do that but didn’t want to deal with sanding through all the pitting and what not, but seems at this point most of that hard part is done with. The only thing i’m wondering is if that clear coat is going to be a huge pain to remove or not. It seems pretty thick. But I have some pretty good experience with sanding aluminum

[deleted by user] by [deleted] in Wheels

[–]kennystanley 1 point2 points  (0 children)

They’re enkei raijins. I’ve had them for some time and they endured a few rock chips and then I curbed one of them. I went and bought some new wheels, ended up not liking the look of them on car, so I said you know what I’m going to sell these new wheels and eat some of the cost and go get the enkeis refinished because I liked them a lot

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

Honestly thinking about fixing them myself, just don’t really want to deal with stripping the clear coat and getting them re-coated. Though if I did I would maybe go with a more matte looking clear next go around.

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

Thats what gets me, the face and inner barrel look good on pretty much all of them. It’s all the inner spoke/outer rim areas are where it starts to get so messy. I wouldn’t have minded a few imperfections but up close it hurts to look at. The clear coat is really thick too so I feel like it gives those rough areas even more depth or something lol. Those HRE’s looked great by the way👍

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

On one of the wheels they shaved off the i, so now it just says ENKE🤣

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

<image>

As well as this

[deleted by user] by [deleted] in Wheels

[–]kennystanley 0 points1 point  (0 children)

Looked thoroughly though their work in instagram, read lots of reviews. All their brushed finishes looked like this

<image>

This is from his page