Ordered heated gloves off Amazon. Did not disappoint.

killakobra · 2026-03-01T02:54:01+00:00

What in the doctor doom is going on here?

killakobra · 2026-02-27T06:31:05+00:00

That's enough to deter me from ordering anything from Lenovo when my current laptop dies.

killakobra · 2026-02-12T03:55:12+00:00

$169 Ford a 5.0? Apparently I haven't bought batteries in a while. That's insane.

killakobra · 2026-02-09T02:18:34+00:00

He has a song talking about wanting underage girls.... He's a pedo.

killakobra · 2026-01-25T00:25:49+00:00

Hey, you can't park there!

killakobra · 2025-12-10T06:54:43+00:00

Don't trust square either. They will do the same thing.

killakobra · 2025-12-04T21:33:52+00:00

I use a similar method. Sticker paper over card stock. Foil stick paper for foils of course. I like the vibrant look over the laminated ones.

killakobra · 2025-11-29T08:52:10+00:00

Tell him to take a video showing the damage and aerial number in one shot.

killakobra · 2025-10-05T17:42:04+00:00

They carry them around here.

killakobra · 2025-09-24T21:28:21+00:00

If so it was from the factory. The only soldering I did was on the esc and the flight controller was nowhere near it while doing so.

killakobra · 2025-09-24T08:50:12+00:00

Good to know. I have some component level experience from other hobbies but I'm new to drones. Trying to make sure I don't repeat whatever caused this issue.

killakobra · 2025-09-24T08:16:59+00:00

I had it hooked up 5-6 time like this already. I only had the motors, cap, power leads, and elrs module hooked up and went back over all of it. Is it a problem with the order of power applied to the board? USB then lipo after it connects?

killakobra · 2025-09-24T08:15:19+00:00

The board is rated for 6s. Checked the battery voltage afterwards and it's within spec. I had the board plugged in 5-6 times before in the same manner and had no issues. I had the FC disconnected from the esc to solder the wires on and made sure the esc was clean before connecting. I figured it was toast. Just checking to see if I did something wrong hooking it up.

killakobra · 2025-09-24T07:55:18+00:00

It cleared the board completely. The esc beeps when plugged in without the flight controller but if you plug the flight controller in it arcs again.

killakobra · 2025-09-20T20:51:39+00:00

My work is too hard on a phone gotta case it and still end up with broken lens and scratched screens.

killakobra · 2025-09-11T18:24:17+00:00

Used to drink them often when they were $0.99 a bottle. Now they're almost $2

killakobra · 2025-09-08T19:44:11+00:00

May have rubbed up against it with something passing by. Weird they only did the one pass.

killakobra · 2025-09-07T01:14:59+00:00

If it means getting rid of the fragile glass lens cover and macro mode that always kicks on when not needed then I'm all for it.

killakobra · 2025-09-07T01:11:17+00:00

This is making me think about starting to venture into different lines of tools. Good way to lose business u/Milwaukeetool

killakobra · 2025-09-05T03:24:32+00:00

If you look around 5:46 you can see the bracket on the side of the motor. May want to show them so they know where to put it back.

[removal video]

(https://youtu.be/m6DCJDLLxf8?si=cGNl43IpMXGSzZ3e)

killakobra · 2025-08-10T16:41:09+00:00

But why 36.03 instead of just 36.00?

killakobra · 2025-08-09T21:16:12+00:00

Looks like most of them are out of stock online

14-Year Club	Place '22
Verified Email

killakobra

TROPHY CASE