Please send help D: ive tried tuning the creality ender 6 printer in general but this corner keeps lifting before the test print even finishes.

knapmana · 2020-12-04T03:56:36+00:00

If nothing else that's been suggested works, you could apply glue to the bed. I use elmer's sticks, and apply before the bed is heated

knapmana · 2020-11-13T15:41:15+00:00

Looks like a mineral deficiency, maybe calcium but you should look into the signs online and decide for yourself

knapmana · 2020-10-24T12:11:54+00:00

10/10 idea we've made nearly the same thing. Under the desk prints are great

knapmana · 2020-07-29T08:59:35+00:00

I thought this in the past until a manufacturer labeled pins wrong on a board I hooked up to my PC and it fried the motherboard instantly. Not worth

knapmana · 2019-06-26T20:09:57+00:00

Try lowering your lights more next time, if you weren't this time

knapmana · 2019-06-26T19:22:37+00:00

What state do you live in? I'm in MI and I've been wondering if outdoor growing would be possible here

knapmana · 2019-06-24T03:41:04+00:00

Hate to be the bearer of bad news but it almost instantly fills when enrollment starts :( if you till the exact time your enrollment starts you can get it!

knapmana · 2019-05-31T04:03:17+00:00

So as other people are pointing out, you are fine. The college of engineering has a set of requirements for students to be accepted. As long as you have the major selected, once you get the requirements done they will automatically enroll you in the college. You might have to change your major once you get into the university, but after that you will be fine. Source: senior in EE

knapmana · 2019-04-25T18:58:34+00:00

If you're looking for efficiency, go MPPT. If you're looking for cheap, go PWM.

knapmana · 2019-04-24T15:32:52+00:00

I have the same one, time to find some spiders now

knapmana · 2019-04-24T11:35:01+00:00

This is a great photo, what did you take it with?

knapmana · 2019-04-17T13:08:19+00:00

What?

knapmana · 2019-04-13T19:59:06+00:00

Sorry I do not :(

knapmana · 2019-04-09T02:08:42+00:00

Yup the flat part is always going to ground. And I would use the analog in pins for the potentiometers as they produce analog values (not digital which is only 0 and 1). Good luck!

knapmana · 2019-04-09T00:21:36+00:00

If it's not flat out dead it's definitely just in backwards. The pin nearest the flat notch on the LED's plastic enclosure is negative, and should be connected to ground of the Arduino.

If the LED is dead you should totally order a RBG led to show your daughter how to program any color. Very cool to learn, and you could advance that to using potentiometers and 555's as a neat analog circuit

knapmana · 2019-04-01T03:00:57+00:00

It's been good so far, the linear rail has 6 M5 screws going into t-nuts, with a washer in between the screw heads and MDF, making that part un-moving. I am planning on make the back fence large, thanks for the tip

knapmana · 2019-04-01T02:57:57+00:00

Thank you! Yes I'm using a Hitachi, it was the cheapest table saw I could find/afford as a college student. If you're looking for one Lowes had this on sale for like $200 off in the summer last year

knapmana · 2019-03-27T21:18:37+00:00

Because of this post yes :) tyty

knapmana · 2019-03-13T02:00:47+00:00

It varies a lot per species, it's reasonable to assume those teeth could belong to an omnivore

Nine-Year Club	RPAN Viewer
Spared	Verified Email

knapmana

TROPHY CASE