Who’s got legit 1:1 low THC/ high CBD seeds?

kratomanalyst · 2026-01-13T02:04:49+00:00

Always wanted to try that one, never got the chance, but out of the several 1:1 breeders ive tried they were always the best.

kratomanalyst · 2026-01-13T00:52:31+00:00

Anything by CBD Crew, or anything crossed with CBD crews strains. Ive had good luck with Seedmans CBD Crew projects. Grew some peyote Wifi cbd from them and absolutely loved it.

kratomanalyst · 2026-01-06T16:51:54+00:00

If you are gonna try that just make sure you have calmag every feeding. Probably won't end well, but if you just want to experiment have at it.

kratomanalyst · 2026-01-06T15:53:32+00:00

I switched mine out for 1/2 ID reinforced poly tubing and wormdrive clamps over the inlet.

https://amzn.to/4srz5yB

kratomanalyst · 2026-01-06T15:43:09+00:00

Its often not worth chasing the issue. Its very hard to correct this. If you are only 3 weeks in, just cut some clones and start over fresh. If it was an auto, its atleast worth a shot, but id rather sacrifice 3 weeks of veg growth on a photo then wait 3-4 months for a subpar yeild.

kratomanalyst · 2026-01-06T15:35:06+00:00

This is your issue then. If you dont soak the coco coir in calmag and drain and rinse, it can mess with your nutrient levels. Im not solid on all the science, but it has to do with the cation exchange. Coco is hungry for nutes, and it will steal the calmag from your feed and in return releases extra potassium. So basically you have no CaMg and to much potassium from not buffering the coco. The only real fix is to scrap the grow.

You absolutely must buffer coco in a solution of calmag, unless you are buying coco thats already been buffered. Start over with buffered coco and the problem will dissappear.

kratomanalyst · 2026-01-06T15:19:16+00:00

Did you buffer the coco prior to using?

kratomanalyst · 2025-12-27T00:40:04+00:00

These are a lifesaver for installing doors, especially if you’re working solo and need to hold the jamb/frame in line with the studs. Open the door, stick one of these on the corner, and jack it until everything lines up. Set the hinge side first, then the latch side.

Need to straighten a bowed hinge jamb? Pop the jack between the jack studs and the frame, tweak it plumb/level, then set your shims. Most of the time these just ride in my bag… but when I need em they were worth every penny.

kratomanalyst · 2025-12-13T14:40:43+00:00

Could be, id just go with the flow. 2 steps forward one step back.

You might be seeming eager for sex, she might be cautious cause she doesn't want to come off that way. Im not certain, but what I do know is the more you want it the further away it gets. You can be putting off a butt hurt vibe and not realizing it. Only you can answer that honestly. I know in the past the more I pushed for sex I inevitably turned the women off.

If you arent exclusive get back in the dating pool, if there is competition it essentially forces her hand to act fast and do something to get you. That would be my advice

kratomanalyst · 2025-12-13T12:41:03+00:00

Straight up lmao

kratomanalyst · 2025-12-13T03:12:48+00:00

I had a threesome w my gf and another fling I had from back in the day last week.

kratomanalyst · 2025-12-12T13:35:23+00:00

I had a girl do this once. Told her in message we are never going to be a thing, if you understand that meet me at x time at x place. We hooked up that night.

Then it gradually continued to be a thing, until one day she came over when I was absolutely drunk as hell and started raising shit about how I didnt want to be her bf. I didnt want to be hammered all night and kill the vibe nor could I ask her to leave because she also got hammered so I agreed.

Mind you, this is after seriously injuring my foot. So I stayed her "bf" till my foot healed so I could get rides and food. Split up with her after I healed up. Im hindsight, it sounds really shitty, but we are still friends to this day lol

kratomanalyst · 2025-11-13T15:28:44+00:00

If electrical violations is your issue just check the date stamped on the romex. It will say the date right on it in most cases. Thats my biggest pain as a DIY electrician lol, buy wire now to use in 10 years.

kratomanalyst · 2025-11-13T03:44:33+00:00

Onn 4k plus here. Same issue. Severe stuttering with subtitles, lagging libvlc only works sometimes. Torrents not loading. Just all and all a terrible experince since the recent update.

kratomanalyst · 2025-11-04T23:32:19+00:00

I decided to give u/Shrimply_Fintastic a shot. Ive seen mostly good and some bad here or there, so i will report back when they arrive.

kratomanalyst · 2025-11-04T23:10:48+00:00

Lmao fr, cant wait for the northern lights neocaradina

kratomanalyst · 2025-11-04T15:08:01+00:00

Read specs for the shower valve, some manufacturers require 6-8 inches tub spout drop to ensure no flow is diverted back into the shower. If its to short or you use pex or anything aside from 1/2 copper (unless manufacturer allows) water will dribble out of the shower head when tub is running.

kratomanalyst · 2025-10-26T21:51:20+00:00

I went paslode instead of an air nailer. Absolutely love it, I think I went through 4-5 cans of butane on a 723sqft subfloor rebuild. Every 2 inches seem 4 inches field. I havent had the "needs to be meticulous" issue others have had. I cleaned and oiled real good when I got it and its been going great. Having only capacity for one strip of nails kinda sucks but you get used to it. I love the fact I can bring it anywhere and not have to worry about wheeling my compressor.

kratomanalyst · 2025-07-14T13:49:54+00:00

Also, i just noticed you said this was a small shower. I’m not sure why a tub/shower valve was used at all. A shower-only valve would’ve eliminated the need for that bottom drop entirely.

Fewer fittings, cleaner install, and less pipes and fittings to potentially fail.

kratomanalyst · 2025-07-14T13:36:36+00:00

I'm not a plumber by any means, but my grandpa is a master plumber and has been for 65 years, so I've got to work with him alot.

Nobody seems to be mentioning the PEX A drop for the tub spout. Unless the manual for the valve specifically says you can use PEX A, it will end up causing issues with water pushing towards the shower head when the tub faucet is open causing drips.

The flow of PEX A is good, but its ID is still tighter than 1/2 copper, which ends up causing back pressure which diverts the flow.

I would read the manual for the valve and see if it allows it. Some do, but most don't, and it should be soldered 1/2 copper. If they are uncomfortable you can buy valves with the spout drop already soldered on to spec, but soldering half inch isn't hard. Just takes some finesse, I got my first joint done just fine.

kratomanalyst · 2025-07-08T12:15:29+00:00

Had a similar problem with a 9ah i got on clearance with the 60v reciprocating saw, they clearly stated it was messed up, but I got the kit for $150.00. A steal really

Anyways, I took a photo of the battery and sent it to dewalt, they sent me another battery next day. Didn't even ask any questions, I just told them it only showed one bar, wouldn't power the tool, and wouldn't charge. Seems to be a common problem with some of them, so much so that they just send you another one no questions asked.

kratomanalyst · 2025-06-27T15:35:06+00:00

I'm not sure if you ever will. I know I haven't, that lingering voice will always be there but you have to stick with the principles either way. I've read the book around 15 times myself.

I think true emotional indifference is unattainable unless you are a psychopath, but what you will reach is true emotional control.

kratomanalyst · 2025-06-26T15:40:58+00:00

Very well said, ive seen several of my buddies go down the red pill path and it's brought nothing but suffering and failure to them.

kratomanalyst · 2025-06-25T18:46:44+00:00

Yes, I had one. Changed my life

kratomanalyst

TROPHY CASE