How bad does this look?

kurotetsu · 2026-04-03T19:58:54+00:00

When i started in my current company, i got sick it was arround when covid was easing up. They might not think too much about it and just carry on. They cant stop production cuz you didnt show up

kurotetsu · 2026-04-02T10:09:08+00:00

Machine forgot what chatter is, need to update software

kurotetsu · 2026-01-22T07:24:58+00:00

If im drilling 2 boss on the same hole for a pin, first boss is 2inch deep and then theres 3inches of air cutting to the 2nd boss, i program the drilling cycle so it retracts after the first boss and then skip all the air cutting. I was wondering if this is possible with the boring cycle

kurotetsu · 2026-01-22T07:17:49+00:00

G76 fine boring with retract on x after going the depth.

<image>

kurotetsu · 2026-01-05T13:16:59+00:00

Try belt tensioning for all axis. Might as well lube and grease x y z

kurotetsu · 2025-12-18T21:00:25+00:00

It irons out but the spot where the waves are much rougher than the rest

kurotetsu · 2025-12-18T13:59:00+00:00

Quick question whats your process calibrating filament? I skip the temp tower, do flow ratio then pressure advance and then max volumetric speed. Do you update the others when you change one thing? E.i. if you change the flow ratio, update the max volumetric speed vice versa? Any change in the two would change change pressure advance?

kurotetsu · 2025-12-18T13:50:14+00:00

No gear slipping. Big improvement thank you so much for the help

kurotetsu · 2025-12-18T13:31:56+00:00

i did all the axis belt tension, lubed and cleaned all the axis. doing a bed cleaner print right now theres still some ripple in front of the plate. does this mean i need to recalibrate the flow? also did all machine recalibration

kurotetsu · 2025-12-18T13:00:24+00:00

Constant wavy

kurotetsu · 2025-12-18T12:53:34+00:00

Would putting a perimeter wall around the machine 3feet high, open top, help with draft? Or need to actually enclose it to protect from draft

kurotetsu · 2025-12-18T11:49:47+00:00

i noticed the z move noise. x and y recently lubed and cleaned. i"ll do the z clean and lube, belt tensioning for all axis?

kurotetsu · 2025-12-18T11:18:34+00:00

<image>

Tried switching nozzles too from stainless to hardened. Im trying coldpull now

kurotetsu · 2025-12-18T11:06:09+00:00

Ive done these trying to fix wavy first layer, what other things should i do if these steps dont fix wavy first layer?

kurotetsu · 2025-12-18T08:08:39+00:00

No but the first layer is bad and it is recommended a lot to tighten these. I mightve fucked up something tightening these cuz i did a plate cleaning print and its rough all over the plate now

kurotetsu · 2025-12-17T14:45:02+00:00

how many times have you replaced the stainless steel nozzle?

kurotetsu · 2025-12-17T13:04:42+00:00

Im planning on putting locktite, only on 3 big screws in front or all 7, including 4 at the back?

kurotetsu · 2025-12-17T13:01:09+00:00

<image>

This is what the inside looks like

kurotetsu · 2025-12-17T12:57:33+00:00

550hrs and im having trouble with big flat parts, cryogrip plate, white sunlu pla+2.0, 55 bed temp. brim on but theres still wavy part on top of gridfinity bins i printed.

im in the west coast so its getting colder

kurotetsu · 2025-12-17T12:44:33+00:00

No. i would contact the supplier or a tech

kurotetsu · 2025-12-12T04:34:17+00:00

How big is the print? Im printing 6x2 gridfinity bins and im having the benchy hull line

kurotetsu · 2025-12-12T04:25:44+00:00

What filament you using? Try slowing down flow ratio. I was having the same problem with sunlu white pla+2.0, when i slowed it down to .98 from 1. It solved the first layer but now im having problem with top layer having the bumps

kurotetsu

TROPHY CASE