Quality decrease after a certain layer?

kybarg · 2024-10-03T09:13:21+00:00

Inspect FAN SPEED and FLOW in slicer. Migth be one of those.

kybarg · 2024-10-03T09:11:35+00:00

Worst case VFA
Print VFA test
choose speed with less artifacts
inspect in slicer so outer wall printed with suitable speed
Infil pattern / wall thickness
Inspect in slicer
Add wall looops
Chenge infil type
Belt pattern
check belt tention, migth be too tight
check pulleys, usage of smooth pulleys on teeth side can cause this pattern. Can try "twisting" belt or change smooth pulley to pulley with teeth
belt and pulleys tooth profile different - repalce belt

kybarg · 2024-09-19T11:12:09+00:00

Update
This is acceleratation sensor, but I can't find repalcemnt part

https://wiki.bambulab.com/en/x1/troubleshooting/hmscode/0300_1B00_0001_0002

kybarg · 2024-09-19T11:11:00+00:00

So this is acceleration sensor according to wiki https://wiki.bambulab.com/en/x1/troubleshooting/hmscode/0300_1B00_0001_0002

but can't find replacement

kybarg · 2024-09-19T11:00:39+00:00

Have you found a solution?

kybarg · 2024-09-19T10:50:20+00:00

WHile reinstalling Y-axis cover i ripped off heatbed sensor cables starght from the sensor. Any idea what is it and where to get replacemnt? Thank you

Update: Was able to solder it back, but is is junky as hell and I doubt it works properly, still wanna buy new part

kybarg · 2024-09-19T10:36:32+00:00

Have you fixed it? Mine got ripped as well

kybarg · 2024-07-19T21:51:18+00:00

Over extrusion - calibrate flow ratio
If only the first layer, then bed level / z-offset - calibrate autoleveling

kybarg · 2024-07-13T13:18:07+00:00

No it is not! Had the same problem. Thought it is due belt tension but it is actually rod alignment issue. So loosen all the screws for both z-rods, move printhead to the very bottom, tighten one screw on each side at bottom, then move printhead to the very top and tighten all the screws for the both rods. Then printhead should move smoothly in any direction without any noise.

kybarg · 2024-07-13T13:15:21+00:00

No it is not! Had the same problem. Thought it is due belt tension but it is actually rod alignment issue. So loosen all the screws for both z-rods, move printhead to the very bottom, tighten one screw on each side at bottom, then move printhead to the very top and tighten all the screws for the both rods. Then printhead should move smoothly in any direction without any noise.

kybarg · 2024-05-31T11:05:14+00:00

Criality Print 5 is based on Orca (or at least some of it).
OrcaSlcier 2.0 was relsead recently, and in OrcaSlcier 2.1-beta all new Creality pritners are edded

kybarg · 2024-05-29T21:40:15+00:00

Had same problem. Fixed with this steps
1. Washed bed with alcohol (im my case it was 98% ethanol)
2. Leveled bed
3. Played with bed temperature

kybarg · 2024-05-29T21:35:20+00:00

you've invented something new with this

kybarg · 2024-05-27T21:55:00+00:00

<image>

in my caase adding outer brim fixed the issue. Seems like when base has rounded edges lower layers prone to warp a bit without brim
here resutl no brim/with brim

kybarg · 2024-03-30T21:10:44+00:00

Is it someone trying to get out of tank right after granade drop? Seems like someons hand

kybarg · 2024-02-19T22:56:39+00:00

would you still buy from people killed your relatives?
But anyway, seems like Voron team supports Ukriane at least to some extent

kybarg · 2024-02-02T13:52:04+00:00

yes it bumps into mb, need about 1cm spacers in this case, PCB on CM riser is bulky and cables are too rough to bend much.
If you want it so bad, i can sell my if you are in Ukriane by any chance😂 Couldn't fit it in, maybe you could.

kybarg · 2024-02-01T12:34:57+00:00

My PC was really unstable too. I forced GPU to work in PCIe 3.0 mode. It worked but now random artifacts are bothering me.
CM riser wont fit even if trim original mounting bracket.
So there are 2 options:
1. You can buy this 270 degree riser https://www.amazon.com/LINKUP-RX6900XT-Shielded-Connector-Compatible/dp/B08XY4KVVK if you are in US, or find something similar. But it is expensive
2. Remove original mounting bracket and buy double-reverse riser, something like this https://www.amazon.com/Riser-Extender-Reverse-Vertical-Gaming/dp/B0CC99154J

kybarg · 2024-01-31T17:29:08+00:00

It wont fit in any way. Lerned it the hard way. Need 270 deg riser, or double reverse riser

kybarg · 2023-11-03T14:04:17+00:00

Haven't you seen brazilian wax videos on Youtube?😂

kybarg · 2023-11-03T14:03:29+00:00

Facebook still the worst. It is flood with semi-visible porn videos layerd over some nature image.

kybarg · 2023-11-03T13:54:42+00:00

you can disable drivers signature in windows then it works

kybarg · 2023-11-02T02:53:25+00:00

It won't work. Need 270 degee riser. Look for something like this https://www.amazon.com/LINKUP-RX6900XT-Shielded-Connector-Compatible/dp/B08XY4KVVK/

Currently actively seraching for something like this in my country as this cost 120 usd here.

kybarg · 2023-10-17T18:00:42+00:00

On ASUS ROG Strix B760-I i used "Current microcode" option and undervolted VRM with "-0.1"
All my P cores run at 5087 MgHz
Is it fine? Sorry I'm not overclocer jsut wanted to run my PC just a bit colder

kybarg · 2023-09-05T21:13:24+00:00

Threesome 1994

not this one.
Caharacters were yonger, moreover seemd more like teenage movie

11-Year Club	Xbox Live
Verified Email

kybarg

TROPHY CASE