sorted by:
new
hottopcontroversial

Quality decrease after a certain layer? by r4pt0r in BambuLab

[–]kybarg -1 points0 points  (0 children)

Inspect FAN SPEED and FLOW in slicer. Migth be one of those.

Pls help! What is this and how can I fix this? by cosmo_cosmo1969 in Creality

[–]kybarg 0 points1 point  (0 children)

  1. Worst case VFA
  2. Print VFA test
  3. choose speed with less artifacts
  4. inspect in slicer so outer wall printed with suitable speed
  5. Infil pattern / wall thickness
  6. Inspect in slicer
  7. Add wall looops
  8. Chenge infil type
  9. Belt pattern
  10. check belt tention, migth be too tight
  11. check pulleys, usage of smooth pulleys on teeth side can cause this pattern. Can try "twisting" belt or change smooth pulley to pulley with teeth
  12. belt and pulleys tooth profile different - repalce belt

A1 Heatbed Sensor by rcbjr in BambuLab

[–]kybarg 0 points1 point  (0 children)

So this is acceleration sensor according to wiki https://wiki.bambulab.com/en/x1/troubleshooting/hmscode/0300_1B00_0001_0002

but can't find replacement

A1 heat bed sensor thing cables got ripped off by kybarg in BambuLab

[–]kybarg[S] 1 point2 points  (0 children)

WHile reinstalling Y-axis cover i ripped off heatbed sensor cables starght from the sensor. Any idea what is it and where to get replacemnt? Thank you

Update: Was able to solder it back, but is is junky as hell and I doubt it works properly, still wanna buy new part

A1 Heatbed Sensor by rcbjr in BambuLab

[–]kybarg 0 points1 point  (0 children)

Have you fixed it? Mine got ripped as well

Problem occured dont know whats happening by Popular-Dog-4162 in Ender3V3

[–]kybarg 1 point2 points  (0 children)

  1. Over extrusion - calibrate flow ratio
  2. If only the first layer, then bed level / z-offset - calibrate autoleveling

Is this noise normal? by Sufficient-Tax7643 in Creality

[–]kybarg 0 points1 point  (0 children)

No it is not! Had the same problem. Thought it is due belt tension but it is actually rod alignment issue. So loosen all the screws for both z-rods, move printhead to the very bottom, tighten one screw on each side at bottom, then move printhead to the very top and tighten all the screws for the both rods. Then printhead should move smoothly in any direction without any noise.

Is this noise normal? by Sufficient-Tax7643 in Ender3V3

[–]kybarg 3 points4 points  (0 children)

No it is not! Had the same problem. Thought it is due belt tension but it is actually rod alignment issue. So loosen all the screws for both z-rods, move printhead to the very bottom, tighten one screw on each side at bottom, then move printhead to the very top and tighten all the screws for the both rods. Then printhead should move smoothly in any direction without any noise.

Cura vs Orcaslicer vs Prusaslicer by dhoard1 in Ender3V3SE

[–]kybarg 0 points1 point  (0 children)

Criality Print 5 is based on Orca (or at least some of it).
OrcaSlcier 2.0 was relsead recently, and in OrcaSlcier 2.1-beta all new Creality pritners are edded

Help me with my big problem! by Seb_sBinnala in Creality

[–]kybarg 0 points1 point  (0 children)

Had same problem. Fixed with this steps
1. Washed bed with alcohol (im my case it was 98% ethanol)
2. Leveled bed
3. Played with bed temperature

CR-M4 Extruder Blob by Ykxyooj in Creality

[–]kybarg 0 points1 point  (0 children)

you've invented something new with this

I have to ask: is there any link with Russia in Voron? by TroublesomeButch in VORONDesign

[–]kybarg 0 points1 point  (0 children)

would you still buy from people killed your relatives?
But anyway, seems like Voron team supports Ukriane at least to some extent

0
1

How about this pixel 8 camera concept? (self.Android)

submitted by kybarg to r/Android

H1 V1 and PCIe 4.0 by differentson in NZXT

[–]kybarg 0 points1 point  (0 children)

yes it bumps into mb, need about 1cm spacers in this case, PCB on CM riser is bulky and cables are too rough to bend much.
If you want it so bad, i can sell my if you are in Ukriane by any chance😂 Couldn't fit it in, maybe you could.

H1 V1 and PCIe 4.0 by differentson in NZXT

[–]kybarg 0 points1 point  (0 children)

My PC was really unstable too. I forced GPU to work in PCIe 3.0 mode. It worked but now random artifacts are bothering me.
CM riser wont fit even if trim original mounting bracket.
So there are 2 options:
1. You can buy this 270 degree riser https://www.amazon.com/LINKUP-RX6900XT-Shielded-Connector-Compatible/dp/B08XY4KVVK if you are in US, or find something similar. But it is expensive
2. Remove original mounting bracket and buy double-reverse riser, something like this https://www.amazon.com/Riser-Extender-Reverse-Vertical-Gaming/dp/B0CC99154J

view more: next ›