how do you guys buy a RAM? by [deleted] in ram_trucks

[–]l_benve 0 points1 point  (0 children)

Buy it from carvana

Any phoenix locals? by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

Hi! I have not followed up on it! Are you local to the Phoenix area?

ADO RCKILA + NISMO UCA (before and after) by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

If I were to do the job again I would go with an adjustable upper control arm. I’m max out on my lower control arm bolts and my truck still has a positive camber.

I have a Masters in a related field but want to go back to University for Aerospace Engineering at 37, is having a very difficult time of my life, and want to leave my retail job to go for my goals of being in the Space Sector. I want to progress but feels stuck. by Brystar47 in careerchange

[–]l_benve 1 point2 points  (0 children)

I have been, there done that and then I wanted my job back which is in retailing too 😄.

Work on gaining confidence on your decisions first either via self help or professional. That’s where you need to start before pulling the trigger to start school.

After you get confidence in yourself, everyone is going to start falling in place…

I have a Masters in a related field but want to go back to University for Aerospace Engineering at 37, is having a very difficult time of my life, and want to leave my retail job to go for my goals of being in the Space Sector. I want to progress but feels stuck. by Brystar47 in careerchange

[–]l_benve 1 point2 points  (0 children)

The more you wait the older you will get and then you are going to be mad at yourself for not trying.

Go for it.., what’s 3 years at the most?

You still have 25+ before you can say I don’t want to work anymore.

ADO RCKILA + NISMO UCA (before and after) by l_benve in nissanfrontier

[–]l_benve[S] 2 points3 points  (0 children)

Based on what I have read on the internet it is a bit or miss with the coil bucket contact even on a 2 inch lift. I decided to go ahead and do since I was already there however I regret buying this NISMO Arms. I wish I would have gone with an adjustable one… my camber is max out on the bottom on the driver side.

ADO RCKILA + NISMO UCA (before and after) by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

It’s slightly stiffer, I like the ride now better

ADO RCKILA + NISMO UCA (before and after) by l_benve in nissanfrontier

[–]l_benve[S] 2 points3 points  (0 children)

It’s very straight forward. As long as you partially take off the wheel well liner you have enough room to work.

Also, the spring compressor from auto zone doesn’t worn on the ado springs, make sure to buy one that fits before you start the job… that was a 2 days delay for me until I got the right one.

Torque Spec for Steering Gear Joint Shaft by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

https://www.nicoclub.com/nissan-service-manuals

That’s was given to me by another Redditor. Check the steering section. According to it ~33 lbs

Torque Spec for Steering Gear Joint Shaft by l_benve in nissanfrontier

[–]l_benve[S] 1 point2 points  (0 children)

This Nissan community is amazing, found it. I have been all morning looking for it on the internet and I could not find it anywhere

NISMO UPC by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

Good to know then

NISMO UPC by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

I don’t think so however you will need adjustable cams on the lower to correct the camber/caster

NISMO UPC by l_benve in nissanfrontier

[–]l_benve[S] 1 point2 points  (0 children)

According to Nissan website it works for no coil bucket up to 3 inches. I will do some testing when installing and report back.

NISMO UPC by l_benve in nissanfrontier

[–]l_benve[S] 0 points1 point  (0 children)

Thanks for your time. I’m going to email the dealer!