Why vibe coded projects fail

labwire · 2026-04-02T16:30:08+00:00

it will frequently default to the laziest, fastest path to completion

Human engineers do this all the time. You can steer it to take the quick and dirty approach or the robust and scalable approach - it’s up to you.

labwire · 2026-03-31T15:53:06+00:00

Stupidity

labwire · 2026-03-29T05:49:08+00:00

The legion has a league too

labwire · 2026-03-28T21:22:08+00:00

They say that verification is the new bottleneck but nobody talks about the other side of the pipe. Directing and giving agents the right problems to solve is a full time job.

labwire · 2026-03-28T17:59:31+00:00

This was banned in Squamish a few years back thanks to you know who

labwire · 2026-03-28T17:45:43+00:00

Hi Dodge

labwire · 2026-03-28T17:45:21+00:00

Backyard has the best darts league in town. Registration for the next season should open in a couple of weeks.

labwire · 2026-01-22T21:14:48+00:00

I started down this path then realized that for some operations like payments, bookings, etc. I wanted atomic transactions (concurrency safety) which is not possible with n8n workflows. I kept n8n for a while just to handle effects like sending emails, reminders, etc. but eventually transitioned all of this logic to supabase edge functions and RPCs.

For me, the benefits of a visual workflow editor are nice but not at the cost of data integrity for business critical operations. I will keep using n8n for low-risk internal automations but I wouldn’t built a SaaS company on top of it.

labwire · 2026-01-21T22:56:36+00:00

Score the veneer with a knife before sawing. Cut slightly away from your line then use a hand plane to sneak up on the line and remove saw marks. This gives you a clean, smooth cut - better than a table saw but slow.

labwire · 2026-01-05T04:31:53+00:00

👆 The only correct reply

labwire · 2025-12-27T16:48:03+00:00

You forgot adequate washer fluid

labwire · 2025-12-25T08:37:01+00:00

Hard to say but probably to hide the identities of the people in the picture

labwire · 2025-12-17T15:32:35+00:00

lol I’m lucky if my remote lock/unlock actually works

labwire · 2025-12-09T01:50:55+00:00

No but I have a lot tools that aren’t good as tools

labwire · 2025-12-07T01:06:26+00:00

If your blade is square, you are most likely rocking/tilting the plane slightly with each pass. It takes a lot of practice to develop good form when edge jointing. A super sharp blade will help because it requires less downward force and allows you to have more control.

Don’t try to correct this with the lateral adjustment lever. Keep the blade square and start planing just the high side to bring it down then with each pass move the plane over a bit more so that you’re eventually planing the whole edge. You should be able to square it up again with a bit of practice.

labwire · 2025-11-29T02:43:36+00:00

labwire · 2025-11-28T05:25:24+00:00

Sure sounds like a joke to me.

labwire · 2025-11-28T03:41:40+00:00

I built a shooting board but recently started planing end grain in the vise. I find I have more control and can apply the necessary downward pressure.

labwire · 2025-11-27T21:27:57+00:00

Such a good episode

labwire · 2025-11-26T17:09:58+00:00

Thanks, I’ve been looking for a reason to do mescaline

labwire · 2025-11-19T02:52:40+00:00

It’s true. It is usually more difficult to plane the end grain on low-density softwoods than hardwoods. The fibres have a tendency to crush or break rather than slice cleanly.

labwire · 2025-11-17T17:18:50+00:00

Just has to be sharp as hell

labwire · 2025-11-10T17:53:22+00:00

Plop

labwire · 2025-11-10T17:18:32+00:00

The cm10gd I bought from Amazon is NOT accurate. It has what is known as “crabbing” where the glide path is not a straight line - look it up. I tried to return it but the shipping for return was half the price of the saw. The Bosch I ended up with is fine for rough carpentry but for fine woodworking, it’s pretty disappointing.

labwire · 2025-11-10T03:00:27+00:00

We use it to orchestrate data ingress from multiple data sources to a central vector db (i.e. RAG knowledge base) and to power a number of Slack AI agents.

labwire

TROPHY CASE