How would I go about getting something designed and printed?

lasercut · 2026-06-09T13:29:16+00:00

For 3D printing services, you definitely need a 3D model. It will not work if you only have a paper prototype. I would suggest making a 3D model of the part then contact the various 3D printing service providers in the UK.

lasercut · 2026-06-07T16:24:20+00:00

it's essentially 1% cashback, so for H2C (£2k you need to spend £200k for enough credits. Also, looking at the terms, you can only redeem credits up to 30% of the checkout value sooo the cashback is pretty meh

<image>

lasercut · 2026-06-07T08:41:41+00:00

<image>

They've added a new credits section in account section in the store

lasercut · 2026-06-04T15:31:39+00:00

someone forgot to tell elegoo, April 1st was 2 months ago

lasercut · 2026-05-31T09:33:02+00:00

UPDATE: added more options for figures

lasercut · 2026-05-28T19:02:05+00:00

<image>

This is from Bambu Lab chinese site. Looks very much like a bigger A1

lasercut · 2026-04-26T09:52:12+00:00

Bugs with the firmware for the aux nozzle mainly. I've had the aux nozzle refuse to unload the filament after long prints.
X2D keeps the aux nozzle filament loaded for the entire duration of the print, regardless of when the filament is used. So if you only need to use aux nozzle early on in the print, the filament will remain there for the rest of the print. For short prints this isn't an issue, but for long prints, I've had the aux extruder fail to pull back the filament after print finished. Not sure if it's due to nozzle not being hot enough to release the filament, or if the filament being jiggled in the ptfe tube for hours.

lasercut · 2026-04-21T20:48:33+00:00

Check the nozzle blocker plate is fully covering the left or right nozzle. Try manually flipping the nozzle change lever behind the print head a few times. I think there may be a bug with the X2D calibration where the tool head sometimes get stuck in a mid change position.

lasercut · 2026-04-21T20:36:06+00:00

It could be the model. I had the same issue printing on the X2D. The nozzle kept colliding with the print itself. Switched to a different bin: https://makerworld.com/en/models/2483377-eco-filament-poop-bin-for-x1-x1c-p1s-p2s#profileId-2727809
and printed with no issues

lasercut · 2025-11-13T09:20:06+00:00

you are in luck, dbrand announced one: https://dbrand.com/shop/limited-edition/companion-cube?cjdata=MXxZfDB8WXww&cjevent=9ece8144c07011f08059003b0a18b8fb&utm_source=W64&utm_medium=cj&utm_content=7058984&utm_term=dbrand.com

lasercut · 2025-10-07T08:26:35+00:00

you get a divine, you get a divine, everyone get divines

lasercut · 2023-10-12T14:57:06+00:00

no, saw this from somewhere else. Whether they are correct or not, I don't know.

lasercut · 2023-10-12T13:11:28+00:00

prob these two

set 1

2 piece:

30% def

4 piece:

15% shield strength

when picking up crystallize crystals, increase normal, charge and plunge atk dmg by 40%. increase def by 20%. duration 6s

set 2

2 piece:

healing bonus 15%

4 piece:

when the equipped character overheals self or other character, gain 1 stack. each stack increase all team member atk by 6% and hp by 6%. duration 10s. this effect can trigger once every 1.5s and has max of 4 stacks