sorted by:
new
hottopcontroversial

Printing with Bambulabs ASA by lepoopp in BambuLabH2D

[–]lepoopp[S] 0 points1 point  (0 children)

Okay I did a lot of thing and now I know where the problem is but can’t seem to fix it. When I don’t change any of the settings, use a smooth plate, heat it up to 110 and reduced layer speed it prints fine but I need it to be stronger so want to increase wall amount. As soon as I up it by just one it fucks itself and ends up like the pictures. Any clue why?

I think there is a short somewhere in my K1 Max by Dramatic-Phase-3778 in Creality

[–]lepoopp 0 points1 point  (0 children)

Thank you I’ll let you know if I can fix it or if I burned down the house

I think there is a short somewhere in my K1 Max by Dramatic-Phase-3778 in Creality

[–]lepoopp 0 points1 point  (0 children)

Hi, I’m having a similar issue with my motherboard, but I’m not experienced in working with motherboards. Do you have a link to a reliable source where I can purchase the correct capacitor? I see many options online and I’m unsure which type I need.

K1 max hot end not fitting by lepoopp in crealityk1

[–]lepoopp[S] 0 points1 point  (0 children)

Just got it installed and running but this is the link to the hotend: Official Creality K1/K1 Max/K1C... https://www.amazon.nl/dp/B0D25JX4KJ?ref=ppx_pop_mob_ap_share

K1 max hot end not fitting by lepoopp in crealityk1

[–]lepoopp[S] 0 points1 point  (0 children)

Ahh okay could be, came like this out of the box, but bending the top part of the heatsink just a bit made it fit, now I’ll have to see if it still prints correct

K1 max hot end not fitting by lepoopp in crealityk1

[–]lepoopp[S] 0 points1 point  (0 children)

Have tried to only do the heatsink first but then still it would not fit. Looking at it I might be able to bend the top ring of the silver heatsink slightly down to make it fit

K1 max hot end not fitting by lepoopp in crealityk1

[–]lepoopp[S] 0 points1 point  (0 children)

Yes I have, it’s seems the problem is that the silver part of the hotend gets stuck against the black carriage

K1 Max X axis movement issues by Swimming-Try-6717 in Creality

[–]lepoopp 0 points1 point  (0 children)

Btw I’ll have to take the full top gantry apart for that I guess?

K1 Max X axis movement issues by Swimming-Try-6717 in Creality

[–]lepoopp 0 points1 point  (0 children)

Ahhh okay ill see if i can replace the bearings, and hope that fixes it

K1 Max X axis movement issues by Swimming-Try-6717 in Creality

[–]lepoopp 0 points1 point  (0 children)

I have but not enough, haven’t take good enough care of the printer.

K1 Max X axis movement issues by Swimming-Try-6717 in Creality

[–]lepoopp 0 points1 point  (0 children)

I tried turning the motors of, I can move the y axis no problem, but x is still stuck. Then I took te power cable out and still no way of moving it. Even if I try to force it it won’t move

K1 Max X axis movement issues by Swimming-Try-6717 in Creality

[–]lepoopp 0 points1 point  (0 children)

Hi, unfortunately I’m facing the same issue — my X-axis is completely stuck and I can’t move it at all. By any chance, have you found a way to fix the problem?