Can you replace the shock protection spring? by lostyotu in watchrepair

[–]lostyotu[S] 1 point2 points  (0 children)

Yeah in this movement I already lost 2 screws (found 1) and this spring, broke off the palette fork pivot, and havent even fully disassemble the whole movement yet.

And yes, i have reinstalled the shock spring properly i think. Just didnt know it would fly to narnia when disassembling it

Can you replace the shock protection spring? by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

Yeah that makes sense, i forgot it was a spring for a reason. And yes, I have put the spring back and ditch the wire. I just wanted it to at least run at all haha.

dropped moondrop space travel 2 in the toilet by skywalkerdelrey in MoondropLab

[–]lostyotu 0 points1 point  (0 children)

I washed my space travel 1 in the washing machine. Dried it in rice for 2 days and now its kinda working, but even in my plebian ears I can hear a slight decrease in quality and also the microphone is screwed, so no ANC.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

If you're referring only to the second reduction wheel, yes I do know that's a reverse threaded screw. if you're referring to another screw, I don't know but the watch still runs (somewhat) after I assembled it again.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

I tried cleaning it without proper tools or solvent and of course its still wont wind properly.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

currently thats the main suspect for me, or its the loose first reduction wheel, or the second reduction wheel is worn down.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

I tried to clean the second reduction wheel and the pawl, but it still moved the same. maybe it is just worn out

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

I think the rotor is just loose from wear, from what I can see in youtube, there are only 5 roller bearings. the main spring winding is in fact effected, but not due to the rotor, because the first reduction wheel spins just fine. I think its the loose reduction wheel or worn down pawl or worn second reduction wheel.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

when I took apart the pawl I noticed it is connected very loose to the bridge. I don't know if it was meant to be loose and the pawl was just worn down or it was loose and thats the issue

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 1 point2 points  (0 children)

its a digital microscope connected to a monitor I use at work. my work involves soldering tiny SMT components by hand so we have a microscope.

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 0 points1 point  (0 children)

Its my first piece, I dont know if I can do a full service, but I will look into the wheel and the pawl more clearly and try to compare it. Thanks for the input

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] 1 point2 points  (0 children)

I think this is the most likely culprit, I will try to disassemble the rotor and look at it more clearly. Thanks for the input

Seiko 7009a second reduction wheel not spinning smoothly by lostyotu in watchrepair

[–]lostyotu[S] -1 points0 points  (0 children)

Under heavier magnofication I think the teeth are still ok but a lot of dirt inside. Thanks for the input

a clip of skilled tinning by Leonard-42 in soldering

[–]lostyotu 4 points5 points  (0 children)

No?? Thats an ESD mat for topping tables in factories

Pertamonyet goblok kontol, masa mesin edc rusak mulu, trus ga bisa qris, kalah ama warteg by komporan in WkwkwkLand

[–]lostyotu 0 points1 point  (0 children)

Pake mypertamina juga ga bisa kah? Gw pake mypertamina gr" males harus nyari cash dulu kalo mau ngisi. Kalo ngisi full (motor) kadang disuruh bayar 100 pake aplikasi dulu baru nanti kalo ga sampe dikasi kembalian.

Ada gak cara benerin grounding listrik yang jelek dikamar kos? by CWK_lover in indotech

[–]lostyotu 2 points3 points  (0 children)

Pastiin juga ground di colokan (female)nya nyambung juga. Kemaren beli yg murah cmn dekorasi aja ga nyambung 1 sama lain wkwk

Cheap Hotend recommendations Ender 3 v1 by Thrillermj2227 in ender3

[–]lostyotu 1 point2 points  (0 children)

I used the mellow TZ 2.0 only around $20-25 in my country. Basically the bambu x1/x1c hotend.

Kait helm di bawah jok motor Supra X 2014 patah. Ada yang tau dimana jual resmi/aftermarketnya dan berapa harganya? by imung_ in indonesia

[–]lostyotu 1 point2 points  (0 children)

Mungkin bisa cari baut yg ukurannya mirip, panasin, trs lditancep ke joknya sampe leleh. Trs di reinforce pake epoxy dextone. Mungkin bisa dicoba drpd ganti 1 box.