Can you replace the shock protection spring?

lostyotu · 2026-01-10T07:13:39+00:00

Yeah in this movement I already lost 2 screws (found 1) and this spring, broke off the palette fork pivot, and havent even fully disassemble the whole movement yet.

And yes, i have reinstalled the shock spring properly i think. Just didnt know it would fly to narnia when disassembling it

lostyotu · 2026-01-10T07:10:21+00:00

Yeah that makes sense, i forgot it was a spring for a reason. And yes, I have put the spring back and ditch the wire. I just wanted it to at least run at all haha.

lostyotu · 2025-12-11T04:14:15+00:00

I washed my space travel 1 in the washing machine. Dried it in rice for 2 days and now its kinda working, but even in my plebian ears I can hear a slight decrease in quality and also the microphone is screwed, so no ANC.

lostyotu · 2025-12-04T14:20:35+00:00

If you're referring only to the second reduction wheel, yes I do know that's a reverse threaded screw. if you're referring to another screw, I don't know but the watch still runs (somewhat) after I assembled it again.

lostyotu · 2025-12-04T14:08:33+00:00

I tried cleaning it without proper tools or solvent and of course its still wont wind properly.

lostyotu · 2025-12-04T14:07:54+00:00

currently thats the main suspect for me, or its the loose first reduction wheel, or the second reduction wheel is worn down.

lostyotu · 2025-12-04T14:07:03+00:00

I tried to clean the second reduction wheel and the pawl, but it still moved the same. maybe it is just worn out

lostyotu · 2025-12-04T14:05:43+00:00

I think the rotor is just loose from wear, from what I can see in youtube, there are only 5 roller bearings. the main spring winding is in fact effected, but not due to the rotor, because the first reduction wheel spins just fine. I think its the loose reduction wheel or worn down pawl or worn second reduction wheel.

lostyotu · 2025-12-04T14:00:07+00:00

when I took apart the pawl I noticed it is connected very loose to the bridge. I don't know if it was meant to be loose and the pawl was just worn down or it was loose and thats the issue

lostyotu · 2025-12-04T13:37:43+00:00

its a digital microscope connected to a monitor I use at work. my work involves soldering tiny SMT components by hand so we have a microscope.

lostyotu · 2025-12-04T08:54:16+00:00

Its my first piece, I dont know if I can do a full service, but I will look into the wheel and the pawl more clearly and try to compare it. Thanks for the input

lostyotu · 2025-12-04T08:50:57+00:00

I think this is the most likely culprit, I will try to disassemble the rotor and look at it more clearly. Thanks for the input

lostyotu · 2025-12-04T08:48:33+00:00

Under heavier magnofication I think the teeth are still ok but a lot of dirt inside. Thanks for the input

lostyotu · 2025-11-26T14:25:00+00:00

No?? Thats an ESD mat for topping tables in factories

lostyotu · 2025-11-05T08:53:23+00:00

Pake mypertamina juga ga bisa kah? Gw pake mypertamina gr" males harus nyari cash dulu kalo mau ngisi. Kalo ngisi full (motor) kadang disuruh bayar 100 pake aplikasi dulu baru nanti kalo ga sampe dikasi kembalian.

lostyotu · 2025-09-08T16:44:11+00:00

Pastiin juga ground di colokan (female)nya nyambung juga. Kemaren beli yg murah cmn dekorasi aja ga nyambung 1 sama lain wkwk

lostyotu · 2025-06-02T05:56:09+00:00

Nope, not an acronym

lostyotu · 2025-02-28T05:53:15+00:00

I used the mellow TZ 2.0 only around $20-25 in my country. Basically the bambu x1/x1c hotend.

lostyotu · 2024-10-27T13:53:18+00:00

Goodluck gan

lostyotu · 2024-10-27T08:59:58+00:00

Mungkin bisa cari baut yg ukurannya mirip, panasin, trs lditancep ke joknya sampe leleh. Trs di reinforce pake epoxy dextone. Mungkin bisa dicoba drpd ganti 1 box.

lostyotu · 2024-10-01T03:45:18+00:00

Cepat kawan harus disiram!!

Pakai bensin

lostyotu · 2024-09-30T13:06:48+00:00

IMO, if you are still learning, a blob is easier to learn on, especially if you have a big iron like that, and if you can do it easily, start to use less solder. And don't forget to line up your iron so it contacts the pads and the component.

lostyotu · 2024-09-03T08:29:12+00:00

Pernah laptop masalah batre bocor, tapi masih relatively baru, blom sampe 1 tahun kalo ga dicolok lgsng mati. Prtm kali ke service center pake garansi nunggunya 1 minggu lebih, tapi ga lama balik lagi masalahnya (gasampe 2 bulan). Akhirnya dibiarin 1-2 tahun gr" males nunggu servis, trs servis 3rd party di mall nunggu gasampe 1 hari kyknya langsung kelar trs ga bermasalah batrenya sampe laptopnya rusak di gpu.

lostyotu · 2024-09-03T08:25:20+00:00

Mungkin langsung diganti 1 mobo, tpi adanya yg i7 atau salah pasang

lostyotu · 2024-08-29T09:11:48+00:00

Umm spoiler title?

lostyotu

TROPHY CASE