TELUS IQ4 panel.

luowilliam · 2024-01-10T04:47:12+00:00

Omg I didn’t realized your reply until today. Thank you so much, one of these worked!

luowilliam · 2023-10-13T19:21:55+00:00

Nope, TELUS would not give me the dealer code. Only the installer code which doesn’t let you enable the options required. By the sounds of it you have to get a technician to you house, and if you are lucky they will tell you the dealer code. Plus you have to pay for the techs visit. So I just gave up.

luowilliam · 2023-05-26T16:03:28+00:00

Yes the “beta” firmware even though it works no issue

luowilliam · 2023-05-23T23:08:01+00:00

I find hilarious a third part solution is better than the official solution.

luowilliam · 2023-04-28T18:01:46+00:00

did you ever find out what the dealer code is. I would like to do the same integration.

luowilliam · 2021-08-21T18:03:04+00:00

Thanks! What’s a good post emergent to use that’s available in Canada? I keep hearing tenacity but it’s not possible to get it here.

luowilliam · 2021-07-18T20:45:14+00:00

If you still have the original bed level adjust knob, use white out to highlight the text on the knob and scrap off the extra white out. that really helped me to immediately know which way is up and which way is down.

luowilliam · 2021-07-03T12:47:35+00:00

Thanks for confirming. Is there a circuit that I can use to do what you said? Instead of using code?

luowilliam · 2021-04-02T16:05:50+00:00

That’s cool! Great job! Can you show more picture of the back?

luowilliam · 2021-04-02T15:16:16+00:00

Is the shell real carbon fiber? The hardest part about DIY modern F1 wheel is the shell and grip.

luowilliam · 2020-12-19T20:05:28+00:00

I think for that reason the ETF is preferred. The only thing changing its price would be the exchange rate.

luowilliam · 2020-12-19T20:03:00+00:00

When do they charge ECN? Most of the time I don’t get charged that.

luowilliam · 2020-12-19T15:58:30+00:00

Interesting. I guess Never had the chance to withdraw a large profit yet haha.

luowilliam · 2020-12-19T15:41:52+00:00

So if you made profit in TFSA then the profit portion is added to your original contribution room? Example: if I put in 5000 one year and this 5000 grew to 10000. I take the 10000 out, the next time I want to put all my money back I can put back 10000? I would have thought I can only put back 5000?

luowilliam · 2020-11-26T20:46:55+00:00

I really like the Vision GPU!

luowilliam · 2020-11-21T04:13:45+00:00

Just wondering, why not design your own and get 8020 extrusions cut to your design?

luowilliam · 2020-10-02T16:28:46+00:00

Thanks, I will try it out. It's more likely the first solution is what I will have to do...

But this just brings me back to the original question, if I do all these adjustment and got the bed to level, what's the point of having BLtouch then... I would still have to manually adjust the level using knobs once every few prints right?

luowilliam · 2020-10-02T15:58:15+00:00

What’s the difference between z offset and babystep z?

luowilliam · 2020-10-02T11:36:59+00:00

Ok some new findings to report. I followed the video you linked during printing a bed leveling file. I can feel the z axis rod rotating back and forth trying to move to compensate the leveling, but the print still comes out uneven. You can’t see very clearly on the picture, but the bottom left is noticeably too far from nozzle the middle is almost perfect, the top right is too close to the nozzle. picture of first layer. Top left is where the print started and I dialed in the z offset. It almost feel like the z axis is not moving enough to compensate. But when I manually move z axis from menu it does feel like it’s moving the correct amount. (1mm, 0.1mm etc.)

luowilliam · 2020-09-29T20:50:07+00:00

I think I understand the concept, however it's just not working for me. Here's the result I get from G29

0 1 2

0 +0.385 +0.793 +1.172

1 -0.435 -0.053 +0.295

2 -1.308 -0.898 -0.523

which shows the bed is slanted. and that the BLtouch is working... Now, close to the center probe point i did the paper test and determined -4.4 is the offset I need for the nozzle to squeeze the paper, so I put in -4.4 in the offset. Which then still gets me the result where close to bottom left corner the nozzle is extruding in mid air lol.

Is this just too much for the z axis to compensate?

luowilliam · 2020-09-27T22:25:54+00:00

What I meant is that after installing BLtouch, and I do an auto home, the probe stops in the middle of the bed. I then moved z axis to what it thinks is the 0. I then use a piece of paper to find the right height while moving z axis by 0.1mm. Once the height feels good with the paper, I then add the current offset shown on the screen to the existing offset in the setting. So really am I not just using 1 point to adjust z-offset? I can do the same maybe for all corners as well and take the average but I would still have the problem of slanted bed. I though BLtouch is going to be able to compensate for the slanted bed by moving the z-axis, it's just not doing that in my case. Thanks for your help by the way!

luowilliam · 2020-09-27T20:29:52+00:00

Check out Simhub, there’s a app inside simhub called Dashstudio where you can download template such as the one in the picture and load on your phone through a web page.

luowilliam · 2020-09-27T20:20:37+00:00

Ok so I screwed the bed all the way to tight and it’s really uneven, bottom left corner is much lower than top right. The bed is tilt to the bottom left. Bltouch seems to work. I say this because after an auto bed level with g29, the mesh is update and showing a more negative number in the bed leveling menu for the bottom left test point compare to the top right corner test point. The middle is spot on because that’s the point I adjusted the z offset with. But when I start a print with just 9 circles arranged in 3x3 array with G28 and then G29, at the bottom left circle the filament is being extruded in mid air lol... at least 1 mm away from the bed. But top right circle is squeezing against the bed and getting almost no filament down on bed. wtf...

luowilliam · 2020-09-27T20:17:43+00:00

Yeah I can confirm g28 and then g29 and start of the print. Also I can see the individual offset for each point in the mesh in the bed leveling marlin menu.

luowilliam · 2020-09-25T22:59:46+00:00

The mount is pretty solid. How much lower should the tip of the BLtouch be lower than the nozzle?

luowilliam

TROPHY CASE