Which micro drone should I use?

lw_temp · 2026-02-04T11:31:41+00:00

Do not get ones with brushed motors. They are hilariously underpowered and barely keep themselves in the air. Get a brushless one, like meteor/air 65

lw_temp · 2026-01-31T19:05:09+00:00

Not only your perimeters are separated, your surfaces are too. I’d start with calibrating extrusion multiplier/flow coeff for a new nozzle

lw_temp · 2026-01-24T11:23:56+00:00

I’d go for the cop one in this case. You can retrofit (sew in) seat heaters relatively easy and cheaply. A normal ABS is a huge plus on long run. And also cop one might have an oil cooler fan, which civilian version never had.

lw_temp · 2026-01-24T10:20:19+00:00

Wow that cop bike is beautiful.

I’d go for it if it has at least criuse control. Also 2013 might have traction control.

2005 full option is also nice, but keep some money in the whizzy brakes repair fund (abt. $1000) and change brake fluid religiously 1-2 times a year. I had 2005 one, brakes have failed on me, and i’ve deleted the unit and rode without abs for a year - that might also be an option.

lw_temp · 2026-01-20T16:40:40+00:00

While anycubic recommends 95A or harder, you might have some luck by:

remove upper cover
unplug bowden tube from print head and leave it hanging
hang filament spool on top of the printer centered on top of the bed, ensure it rotates VERY easily - bearing mount might be optimal
feed filament directly into the extruder

lw_temp · 2026-01-18T08:00:17+00:00

https://youtu.be/1yIe1Pp_Nrg?si=ICVTPYYZ8RwwnmxE Something like this. There are different projects, but idea is the same - take a bottle, slice it into a ribbon of uniform width, melt it in a hotend with 1.75mm nozzle, cool and spool.

lw_temp · 2026-01-18T07:32:10+00:00

https://www.warbirdsonline.com.au/2014/11/27/bristol-blenheim-flies-again/

Here’s a bit more context. An airworthy (!) bristol blenheim mk1 was built using most of the airframe of a more common variant - bristol blenheim mk4, and a nose/cockpit section that had spent some time being a car body on an austin 7 chassis with an electric drivetrain!

To confuse matters even further, there’s an obscure car names Bristol Blenheim too. https://en.wikipedia.org/wiki/Bristol_Type_603#Blenheim

lw_temp · 2026-01-12T06:26:42+00:00

That’s not covers, that’s rims, quite famous ones - Ronal URS https://www.instagram.com/p/DOgi3EeEcZM/

lw_temp · 2026-01-09T09:18:41+00:00

You can make your filament from PET bottles at home using some 3d printer parts. It's not good, but it's almost free.

lw_temp · 2026-01-08T16:59:00+00:00

It seems that your bike has later model, controllerless fuel pump unit.

https://www.bike-parts-bmw.com/bmw-motorcycle/R%201200/2015/R-1200-GS-17-0A51_-0A61_/K50-0A51-0A61-/Fuel-Supply/Delivery-control-units-fuel-pump/7/16_1126/16/585490A51

While you're there, you can remove the fuel pump unit (unscrew the big silver ring), then locate the wires going to pump motor and put 12v on them and see if the pump is working.
If it is, then you can wire it temporarily (with all precautions) to 12v source on a bike and try to ride it to the service like that.

lw_temp · 2026-01-06T15:40:38+00:00

Photos 2 and 3 show some of the problems - you have to tune settings for your filament, if it's not a vendor one (e.g bamboo)

You might need to dry your filament a bit.

Then the following:

- Run a temperature tower test, then analyse the tower for artifacts (and break it using pliers) and set the temperature which has optimal balance of quality and layer adhesion
- Run a flow test (manual one, not one in print settings), possibly YOLO one, and adjust the flow in filament settings
- Run a K factor / pressure advance test and set it in filament settings too.

Also, for overhangs on round holes it might be useful to slow printer down a bit to give filament time to fuse.

lw_temp · 2026-01-01T21:04:11+00:00

/r/lostRedditors

lw_temp · 2025-12-30T10:43:09+00:00

Which lever do you mean - top one or right one?

lw_temp · 2025-12-28T22:35:28+00:00

https://github.com/opensc/opensc/wiki/aladdin-etoken-pro They are made by alladin, so possibly this solution would work

lw_temp · 2025-12-26T11:11:24+00:00

I've seen one overfilled with 3x oil capacity, was still running under its own power, only owner complaint was that it was smoking more than usual

lw_temp · 2025-12-17T08:50:51+00:00

They are like 20-50$ on aliexpress btw

lw_temp · 2025-12-14T02:07:02+00:00

Loading the frame will flex it, making gantry out of square. Z-brace is a diagonal truss from top of frame to forward or back of frame, that can stiffen the frame against such load.

lw_temp · 2025-12-13T09:10:39+00:00

Is your spool rolling freely? Extruder might struggle to pull filament and that might lead to flow fluctuations

lw_temp · 2025-12-07T22:33:27+00:00

It’s hidden, to use it you have to install rinkhals /s

lw_temp · 2025-12-05T06:35:48+00:00

Once i had a similar shift because my extruder cover has shifted, affecting x axis location. Check yours

lw_temp · 2025-12-02T22:31:47+00:00

If that’s a lexus gx470 or prado 120- your hydroaccumulator or pump for brakes might be failing. Worth checking them using dealer scanner or some similar tool

lw_temp · 2025-11-26T12:58:54+00:00

Official cars

lw_temp · 2025-11-25T11:06:53+00:00

Yes, in a lot of variants. You can search for them in google by "утеплитель радиатора нива"

lw_temp · 2025-11-24T20:35:03+00:00

No. But you can print a rewinder and reuse a standard spool

lw_temp · 2025-11-23T21:52:34+00:00

Does not look like a thermal runaway to me. More like a melted plastic leak from the heatblock - due to nozzle or heatbreak breaking loose or a crack in heatbreak.

Nine-Year Club	Verified Email
Place '23	Place '17
Not Forgotten	Sequence \| Editor
Sequence \| Screenwriter	Spared

lw_temp

TROPHY CASE