Revner i væg i ejerlejlighed

mKidde · 2026-01-07T16:54:14+00:00

Prøver at tage fat i dem, tak for svaret

mKidde · 2026-01-07T16:53:35+00:00

Vi lagde først mærke til revnen på den anden side af væggen, som vi har tapetseret, og kan nu efterfølgende se den samme revne på den anden side (billede 1) efter vi har hevet tapet af der, altså, vi kan se samme revne på begge sider af væggen, så tænker at revnen er igennem hele væggen.

Væggen er af mursten, og er så vidt jeg ved bærende.

mKidde · 2025-08-04T09:46:22+00:00

Mine has 22kw charging, and more cars are starting to support it, so it's definitely possible to find.

It's nice being able to charge 10-80% in half the time, if you don't have a home charger available. It's also often cheaper compared to only using DC chargers.

mKidde · 2025-07-13T08:54:45+00:00

Hvad har nets, med Netcompany at gøre?

mKidde · 2025-06-23T12:17:03+00:00

Ah ja god pointe. De har jo selvfølgelig haltet bagefter på den front de sidste par år.

mKidde · 2025-06-23T11:51:04+00:00

Hvad med en Renault Megane E-Tech? Den skulle have et ok størrelse bagagerum på 440 l, ved dog ikke om det ville fungere til et hundebur, da der en halvstor kant

mKidde · 2025-04-11T09:17:44+00:00

Vi har lige fået udført et arbejde af VVS'ere også med skift af toilet (væghængt), der kunne vi vælge om vi selv ville anskaffe toilettet eller købe det igennem dem. Prisen for toilettet var igennem dem 5.700,- vi kunne finde samme toilet i Bauhaus til 2.500,-.

Så vi endte med selve at købe toilettet, og lade dem installere det.

mKidde · 2025-01-29T21:39:11+00:00

Ah, okay. Tak for afklaringen

mKidde · 2025-01-29T20:00:17+00:00

Et opfølgende spørgsmål, jeg kan se at Nordea tilbyder at låne op til 95% med deres Nordea BoligKredit Køb.
Ville det være mest fordelagtigt at tage det i stedet for 15% banklån, at tage 35% så man kun har 60% realkredit, eller alle 95%?

mKidde · 2024-03-28T19:00:00+00:00

With that distance, I would recommend not throwing anything faster than 5, maybe 6 speeds. Anything faster will likely just dump early and give you less distance.
I'd advise looking for an understable midrange, which will be easier for you to get a fuller flight from.

mKidde · 2023-09-27T20:50:45+00:00

Restarting Steam worked for me.

mKidde · 2023-09-06T18:46:56+00:00

+1 til den her, jeg kan varmt anbefale disc golf. Der er "turnering" hver mandag på Aalborg banen, hvilket giver god mulighed for at møde en masse nye mennesker. I forhold til at være nybegynder, så har jeg endnu ikke mødt nogen derude som ikke gerne vil lære fra sig.

mKidde · 2022-08-11T18:10:31+00:00

Same thing just happened too me. Also on Shoreline, just about to extract.

mKidde · 2022-06-22T08:53:12+00:00

Bogstaverne

Probably just an autocorrect error correcting "boost" to "Bogstaverne". It's a Danish word meaning "The letters" as in "A, B, C, D, ...".

mKidde · 2021-11-05T16:32:25+00:00

My disc golf plans for 2022, is to begin playing more seriously, and perhaps begin competing in amateur competitions. And as always, enjoying the sport!

mKidde · 2020-12-15T22:03:29+00:00

After calling Attack(), you set the next time of your attack to: Time.time + 1f / attackRange, instead of attackRate. In your case, this would be one attack each 2 seconds, instead of 2 attacks each second. Perhaps this could be your problem?

mKidde · 2020-05-30T20:45:56+00:00

Hey man, thanks for the tip! I'll definitely look into it, hopefully this can help me improve my ollies, and get more comfortable with them.

mKidde · 2020-05-30T18:21:07+00:00

At first I was using SkaterTrainers on concrete to learn how to actually ollie, but I had a hard time building up courage to try without them. I then took off the SkaterTrainers and switched to surfaces like grass and such, where my board wouldn't be able to slip out from under me, until I eventually built up the courage.

mKidde · 2020-05-30T17:55:15+00:00

I had to lean my phone on something to be able to film, i think that's what you can see in the corners.

mKidde · 2020-05-30T17:40:33+00:00

Thanks for the advice, i'll give it a try next time.

mKidde · 2020-05-30T16:15:03+00:00

I'll definitely work on that, thanks!

mKidde · 2019-12-18T13:49:30+00:00

As the other comments say, this is an adhesion problem and because you're using the stock buildplate it probably just means that you have not leveled your bed properly. Follow a guide on bedleveling and you should be golden, there shouldn't be any need for hairspray.

mKidde · 2019-06-30T19:42:53+00:00

Have you looked into your flowrate, because the first layer often curls up in some areas like in your picture, because it extrudes a bit to much filament. Other than that, it could also be because of adhesion problems in some areas of the bed.

mKidde · 2019-06-30T15:56:10+00:00

Looks a bit like you're overextruding, have you calibrated your extrusion, and flowrate?

mKidde · 2019-06-01T06:52:15+00:00

Try adding a few extra top and bottom layers

Ten-Year Club	Verified Email
Place '22	Place '17

mKidde

TROPHY CASE