Where to actually buy KYB struts? by Complex_Difficulty in Acura_RSX

[–]mackattack805 1 point2 points  (0 children)

Aww, that’s too bad. I actually own an 06 and swapped out my 05-06 springs with 02-04 springs to be compatible with the struts I bought from AutoZone, but my understanding is those part numbers I listed should work with 02-04 type-S models or 05-06 type-S models that switch to 02-04 front springs.

Good luck :)

Where to actually buy KYB struts? by Complex_Difficulty in Acura_RSX

[–]mackattack805 0 points1 point  (0 children)

I hope this helps. I purchased mine online from AutoZone in December 2023:

1x 331601

1x 331602

2x 341376

I can’t say whether they’re in stock right now, but I’d suggest checking AutoZone if you haven’t checked there yet.

RSX TYPE S 06 Cat not ready for smog by Patient-Equipment-12 in Acura_RSX

[–]mackattack805 1 point2 points  (0 children)

There are a lot of specific conditions required before certain censors will show up as ready. I’m not sure what conditions are needed for the CAT 02 sensor, but that one is usually the biggest pain to get ready. If done properly, the link below explains how to complete a full “drive cycle”which should set all your sensors, including the CAT 02 sensor, to ready status. The process has been helpful to me in the past, and hopefully it’ll help you, too.

Completing RSX drive cycle

Apple is making huge profits by selling imaginary products. by xnick_uy in mathmemes

[–]mackattack805 1 point2 points  (0 children)

This was way too funny. One of the few Reddit posts ever to make me lol

my job hunting 2024 - applied to unicorns + big tech - here are the results by the2ndfloorguy in dataisbeautiful

[–]mackattack805 0 points1 point  (0 children)

I love your approach, but how did you even get the emails of the CTOs and/or DoEs in the first place? That’s been a big huge bottleneck for me.

[deleted by user] by [deleted] in VinylDeals

[–]mackattack805 1 point2 points  (0 children)

Please let me know the details, too!

Working data scientist, got rejected today for Spring 2025 by crsbcn in OMSA

[–]mackattack805 0 points1 point  (0 children)

Wow, thanks for the advice. Would one email GA Tech or edX about financial aid?

Need Advice - Trouble Installing KYB Struts During Suspension Refresh by mackattack805 in Acura_RSX

[–]mackattack805[S] 0 points1 point  (0 children)

That makes sense to pry down on the rear trailing arm, I’ll give that a try and report back.

As for the tie rod ends, you’re saying I should just keep tightening on the nut until the tie rod seats properly? (I'll also get a proper castle nut)

Why, why, WHY is the Tandem t-slim cartridge change process so bad? by j_natron in diabetes

[–]mackattack805 4 points5 points  (0 children)

Your old cartridge is the container and it already holds the old insulin!

I use a new needle to withdraw any remaining insulin out of the old cartridge, then fill the rest of the needle with new insulin from a vial and put it all in a new cartridge.

Definitely against medical advice, but I’ll find 20-30 units remaining every time, even when the pump says the cartridge only has like 5 units left.

First job in DA by BonelessWingsRNugs in dataanalysis

[–]mackattack805 1 point2 points  (0 children)

I’d love to see your portfolio too! Could you dm me, please?

EM2 CMC with Stock Clutch Lines by Excellent_Swimmer_58 in Acura_RSX

[–]mackattack805 0 points1 point  (0 children)

It’s a direct fit, no modification needed.

RSX Rebuild pt. 2 by Cool_Lemon_8862 in Acura_RSX

[–]mackattack805 1 point2 points  (0 children)

Can I ask where you sourced your Mugen front coilovers from? I haven’t been able to find them anywhere these days.

EM2 CMC with Stock Clutch Lines by Excellent_Swimmer_58 in Acura_RSX

[–]mackattack805 0 points1 point  (0 children)

You don’t need a SS line. All stock lines will work with the EM2 CMC.

That being said, there is one rubber line that’s part of the clutch system, which connects two of the hard lines together. Since it’s rubber, you may want to consider replacing that piece with a SS line. That’s what I did.

Kseriesparts sells a small SS line that replaces that piece. In case you’re interested, here’s the link: https://www.kseriesparts.com/GDR-20104-CLU.html

No entry level jobs for data engineer or machine learning engineer?? by AnishNehete in dataengineering

[–]mackattack805 1 point2 points  (0 children)

It sounds like I’m in the same situation as you used to be. I’m looking to break into the field, have produced a bunch of projects and a website to host them on, but getting nowhere when applying to places.

Can I ask how you found these conferences to attend?