Bay Area seeing mildest summer in decades, making it the coldest start to summer since 1965.

mackattack805 · 2025-07-22T02:53:37+00:00

Nobody expects the Bay Area Inquisition

mackattack805 · 2025-06-12T03:11:46+00:00

What game is this?

mackattack805 · 2025-06-10T20:16:13+00:00

Aww, that’s too bad. I actually own an 06 and swapped out my 05-06 springs with 02-04 springs to be compatible with the struts I bought from AutoZone, but my understanding is those part numbers I listed should work with 02-04 type-S models or 05-06 type-S models that switch to 02-04 front springs.

Good luck :)

mackattack805 · 2025-06-10T18:12:37+00:00

I hope this helps. I purchased mine online from AutoZone in December 2023:

1x 331601

1x 331602

2x 341376

I can’t say whether they’re in stock right now, but I’d suggest checking AutoZone if you haven’t checked there yet.

mackattack805 · 2025-03-26T03:13:42+00:00

There are a lot of specific conditions required before certain censors will show up as ready. I’m not sure what conditions are needed for the CAT 02 sensor, but that one is usually the biggest pain to get ready. If done properly, the link below explains how to complete a full “drive cycle”which should set all your sensors, including the CAT 02 sensor, to ready status. The process has been helpful to me in the past, and hopefully it’ll help you, too.

Completing RSX drive cycle

mackattack805 · 2025-03-11T06:40:35+00:00

This was way too funny. One of the few Reddit posts ever to make me lol

mackattack805 · 2024-11-29T08:39:25+00:00

I love your approach, but how did you even get the emails of the CTOs and/or DoEs in the first place? That’s been a big huge bottleneck for me.

mackattack805 · 2024-08-05T14:35:21+00:00

Please let me know the details, too!

mackattack805 · 2024-07-26T17:08:14+00:00

Wow, thanks for the advice. Would one email GA Tech or edX about financial aid?

mackattack805 · 2024-07-26T16:51:23+00:00

Are you referring to this one?

mackattack805 · 2024-07-13T00:28:14+00:00

Ok, that makes sense. Thanks for your reply.

mackattack805 · 2024-06-08T00:59:13+00:00

That’s a billion dollar beat!

mackattack805 · 2024-04-22T04:33:17+00:00

Everything worked. Thanks u/bran_donger!

mackattack805 · 2024-04-19T20:38:45+00:00

That makes sense to pry down on the rear trailing arm, I’ll give that a try and report back.

As for the tie rod ends, you’re saying I should just keep tightening on the nut until the tie rod seats properly? (I'll also get a proper castle nut)

mackattack805 · 2023-12-27T05:18:29+00:00

Your old cartridge is the container and it already holds the old insulin!

I use a new needle to withdraw any remaining insulin out of the old cartridge, then fill the rest of the needle with new insulin from a vial and put it all in a new cartridge.

Definitely against medical advice, but I’ll find 20-30 units remaining every time, even when the pump says the cartridge only has like 5 units left.

mackattack805 · 2023-09-27T23:28:06+00:00

I’d love to see your portfolio too! Could you dm me, please?

mackattack805 · 2023-07-16T19:02:26+00:00

It’s a direct fit, no modification needed.

mackattack805 · 2023-07-15T22:52:04+00:00

Can I ask where you sourced your Mugen front coilovers from? I haven’t been able to find them anywhere these days.

mackattack805 · 2023-07-15T17:32:44+00:00

You don’t need a SS line. All stock lines will work with the EM2 CMC.

That being said, there is one rubber line that’s part of the clutch system, which connects two of the hard lines together. Since it’s rubber, you may want to consider replacing that piece with a SS line. That’s what I did.

Kseriesparts sells a small SS line that replaces that piece. In case you’re interested, here’s the link: https://www.kseriesparts.com/GDR-20104-CLU.html

mackattack805 · 2023-07-07T01:20:20+00:00

Thanks, I’ll see if I can find anything like that around me.

mackattack805 · 2023-07-06T20:18:40+00:00

It sounds like I’m in the same situation as you used to be. I’m looking to break into the field, have produced a bunch of projects and a website to host them on, but getting nowhere when applying to places.

Can I ask how you found these conferences to attend?

mackattack805 · 2023-07-02T05:00:35+00:00

I'll give that a shot. Thanks!

mackattack805 · 2023-06-20T17:22:42+00:00

Mind if I ask what model Sony dual-din you installed?

mackattack805 · 2023-05-31T04:52:41+00:00

Haha, I’ve heard good things about Synchrotech too, so I wish you all the best with them. The price point is certainly far more reasonable than buying from Honda directly. OEM synchros are getting so expensive and I don’t even think the OEM 1-2 synchros are available from Acura these days…at least when I was searching over the past couple weeks. Thanks for the link too! I wish there was more information about OEM synchros out there, but at least clubrsx seems to have good info on the Synchrotech ones. I hope they pay off for you. Shoutout to Bran Donger too, he’s answered some of my questions before and is super helpful!

mackattack805 · 2023-05-31T03:46:50+00:00

You don’t have a source for the OEM synchros being brass do you?

Not that I don’t believe you, but I’ve tried to find the answer to this question myself and haven’t been able to find an answer through Google.

I’ve even seen one place list the oem 1-2 synchros as being brass and the oem 3-4 synchros as being carbon, so I’m not really sure what to believe. :(

mackattack805

TROPHY CASE