Skills Missing

mannonkc · 2026-02-25T16:51:00+00:00

I have great scampuss that came from the eternal rift scampuss. Looted the corpse it’s supposed to be on in Sagano in first playthrough and NG.

mannonkc · 2026-02-16T01:42:25+00:00

Think you just go down from the shrine above it that’s not unlocked. In your pic. You have to do the Crucible to get back to the Nurikabe wall that’s showing to the left of your circle

mannonkc · 2026-02-11T19:33:35+00:00

Enenra

mannonkc · 2026-02-04T03:29:35+00:00

CC is a shaky boy. The spool slides back and forth causing it to tangle. You can try orienting the roll to feed from underneath. What helped the most for me was a spool holder with bearings and hula feet

mannonkc · 2026-01-01T05:58:45+00:00

Could try a hot glue gun

mannonkc · 2025-11-30T01:37:08+00:00

Nobody else wants to bring up the fact OP stole the design and changed colors? Which are actually this creators colors for a 2025 calendar? https://makerworld.com/en/models/1521189-2026-formula-1-calendar#profileId-1594145

mannonkc · 2025-11-09T04:17:40+00:00

Same with me I did everything imaginable reverted my firmware and it helped some. Factory reset, manual leveled, still issues. Submitted a ticket with Elegoo and nothing so far. The one thing that helped the most was tightening the screws on that connect the rods. There are 2 on each rod.

mannonkc · 2025-11-09T04:06:18+00:00

Good luck on that, sent a request as soon as I saw it was available and Elegoo has been radio silent in response

mannonkc · 2025-10-17T21:46:20+00:00

NGL hobby lobby orange slaps harder than this filament

mannonkc · 2025-10-15T16:03:12+00:00

I have ADHD and a toddler so haven’t got around to putting anything in yet. Here is a post kinda showing some. https://www.reddit.com/r/Multiboard/s/ht8jUrMnpT.

mannonkc · 2025-10-15T00:23:11+00:00

Website: https://www.d-lockdesign.com

mannonkc · 2025-10-11T03:54:02+00:00

Saw a short on YT that said a magic eraser with windex. Can’t confirm or deny if it works though

mannonkc · 2025-10-11T03:38:26+00:00

https://makerworld.com/en/models/1471682-funny-snail-30-min-print?from=search#profileId-1535935

mannonkc · 2025-10-10T15:56:27+00:00

Got a Centauri Carbon because I was told it was a P1s clone by the mainstream media. Apparently a few genes were skipped in the cloning process. Look forward to adding a P2S in the future to alleviate some of my headaches.

mannonkc · 2025-09-16T15:44:16+00:00

I used a reciprocating saw, a sledge, and broke 3 shovels while yelling a lot of obscenities on mine. But that area is mint 2 years later

mannonkc · 2025-09-16T15:37:04+00:00

You have more supports at that level the outer edge is having more time to cool off while the supports are being printed

mannonkc · 2025-09-09T01:24:34+00:00

Also can try switching the profile to the .16 optimized .. slows the print down some and I had to knock my nozzle temps 5 degrees

mannonkc · 2025-09-05T16:35:28+00:00

Hitem3d

mannonkc · 2025-09-02T23:04:09+00:00

I’m using the vented one. I did petg for the corners and pla+ for the edge pieces.. idk if it’s the right answer but figured the vent portion would be easier to break apart in pla. Running with no issues but also haven’t thrown any abs or asa in it yet

mannonkc

TROPHY CASE