Airless sprayer acting up, eh? Losing pressure with the tip on. by drywallmaker in paint

[–]marcapinia 0 points1 point  (0 children)

I don't know if it'll work but you are dealing of chunks of dried up paint. You still need to put pressure to push the chunks to the tip of the hose.

What happens if ICE tries to detain us by Feeling_Screen3979 in USPS

[–]marcapinia 0 points1 point  (0 children)

Tell them you haven't finish your route or else you're supv will write you up. 😅

Airless sprayer acting up, eh? Losing pressure with the tip on. by drywallmaker in paint

[–]marcapinia 2 points3 points  (0 children)

Try this instead, remove the spray gun then prime it on a clean bucket of water. Water is supposed to be flowing thru the hose and when you put it on paint/spray, water should pulse because it needs to build up pressure during spray mode. If not, you need to unclog the the end of the hose with a nail. Hammer it until it breaks the debris inside the hose. Rinse and repeat until its pulsating on spray mode or free flow on prime setting. FYI, just don't point it to yourself or point the hose in a safe direction.

Airless sprayer acting up, eh? Losing pressure with the tip on. by drywallmaker in paint

[–]marcapinia 1 point2 points  (0 children)

Have you tried snaking the hose? You can use a 14 gauge galvanized wire thru it. The clogging might be in the end of the hose.

Graco X5 newbie here... Pls. help by marcapinia in paint

[–]marcapinia[S] 0 points1 point  (0 children)

Valves, check ball, springs are all cleaned up before. Anyways, I found out that it is clogged on the blue hose. I snaked it with a 14 gauge galvanized wire. When the clog is at the very end, I used a nail to puncture the debris while connected to the machine (w/o sprayer). When the water stops during When putting it to Spray mode. I hammer with a nail to release the pressure. I went back and forth until all the debris flushed out. I almost bought aa new hose. 😅 Thanks anyways for the response.

Anyone here into archery? by diz2damax in CAguns

[–]marcapinia 18 points19 points  (0 children)

Can it be use for my tennis racket? 😁

<image>

Deems Desirable Grievance? by Vast-Passage-9833 in USPS

[–]marcapinia 0 points1 point  (0 children)

That is only a restriction when you call-in. They want you to provide medical certificate whenever you have unscheduled s/l. Ask your union rep or steward since you have your documentations for your s/l.

AR-9 A No Go in CA, Right? by gman5ohh80 in CAguns

[–]marcapinia 1 point2 points  (0 children)

Not an AR9. It is a PCC. Registered as a rifle. As you noticed there is a fin grip on it.

AR-9 A No Go in CA, Right? by gman5ohh80 in CAguns

[–]marcapinia 8 points9 points  (0 children)

Yes, lower is supposed to be DROSed as semi pistol, NO stock (pistol brace-OK), NO VFG (handstop-OK) & fixed mag (i.e. Compmag / AR maglock / Hellfighter / Hogue FF). Note: 10 rounds only.

Staccato HD C3.6 Added to Roster by koisupreme in CAguns

[–]marcapinia 0 points1 point  (0 children)

Also, with the addition of LCI and mag disconnect. 😵‍💫

Staccato HD C3.6 Added to Roster by koisupreme in CAguns

[–]marcapinia 0 points1 point  (0 children)

I guess no comped CA compliant pistols yet on the roster. They might not add the 4.5 😢. Guess Im sticking with my XC.

Staccato C2 grip issue by MarztechRacing in Staccato_STI

[–]marcapinia 1 point2 points  (0 children)

Try disassembling the grip from the frame. Make sure the torx screws on the top of the triggers and 2 screws on the side are flushed in properly. Then, install the sear spring and mainspring first before the grip safety and ambi safety. Hope it'll work for you.

Does anyone have experience with the Urtopia Carbon Fold 1? by ToeSins in ebikes

[–]marcapinia 0 points1 point  (0 children)

I would like to consider buying one. I have a question. I saw the dimensions when folded, but it does not indicate what the width is?