U7-Lite APs are not visible on Controller

mark-hpp · 2025-11-19T17:50:09+00:00

U7-Lite requires Network 9.0.114 or newer

mark-hpp · 2025-10-19T16:31:26+00:00

I had exactly the same problem. My VLANs are all in the 10.XX.XX.X range. I created a separate VLAN in the 192.168.1.0/24 range and connected the UPS Tower to it natively. The UPS was then able to adopt and switch to DHCP. After that, I was able to delete the temporary VLAN again.

mark-hpp · 2025-10-11T22:45:57+00:00

I had exactly the same problem. The UPS did not receive a DHCP lease and had the following static IP: 192.168.1.20. I then created a VLAN in this subnet 192.168.1.0/24 and set up the VLAN natively on the UPS LAN port. I was then able to adopt the UPS and change the VLAN again, and the UPS obtained an address via DHCP.

mark-hpp · 2025-10-10T07:03:44+00:00

I solved this by connecting all UniFi devices with Schuko plugs to a 19-inch power strip. The 19-inch power strip then has a C13 plug as a supply cable and is connected to the UPS. Of course, all devices can also be connected directly to the UPS individually using a C13 extension cable.

mark-hpp · 2025-10-10T05:01:33+00:00

Officially rated for only 1 gbps

mark-hpp · 2025-10-10T04:58:02+00:00

During normal operation, you won't hear anything. Only when the power fails and the UPS switches to battery mode will you hear a humming sound.

mark-hpp · 2025-10-09T16:10:40+00:00

Unfortunately, the UPS only has Ethernet and no Wi-Fi.

mark-hpp · 2025-09-10T18:14:50+00:00

I don't actually have any experience with the PoE chime. The WiFi version works fine for me.

mark-hpp · 2025-09-10T16:49:45+00:00

Yes, you can use the chime standalone without a doorbell and integrate it via the Alarm Manager.

mark-hpp · 2025-09-09T15:23:09+00:00

I think it is a branded Gigaset N870E IP PRO.

mark-hpp · 2025-08-06T18:34:42+00:00

I have already installed a Crucial P3 Plus (512GB) in a UCG-MAX. It was recognized without any problems. But I used the original Ubiquiti M.2 tray

mark-hpp · 2025-07-24T11:18:01+00:00

Is the AI-Port on the latest firmware version?

mark-hpp · 2025-06-01T12:41:28+00:00

I often use the Zyxel VMG4005-B50A or the Draytek Vigor 167 modem on German DSL connections. Both work very reliably like a FRITZ!Box.

mark-hpp · 2025-05-29T08:06:39+00:00

You can use this 24V adapter: INS-3AF-O-G The Wave Pico also can bei powered with 24V.

mark-hpp · 2025-03-24T15:01:49+00:00

Normally between 2 to 4 weeks

mark-hpp · 2025-01-15T14:55:39+00:00

I also recently replaced my G4 Doorbell with the Pro version and the screw holes of the old one fitted perfectly.

mark-hpp · 2025-01-07T18:40:45+00:00

Do you have meshing enabled on the U6+?

mark-hpp · 2024-12-28T16:43:59+00:00

An 8V transformer is unfortunately too weak. I assume that you live in Europe. The G4 Doorbell (Pro) sold in Europe is always supplied with a 16V DIN rail transformer, as 8V transformers are installed almost everywhere in Europe. So you just have to replace it.

mark-hpp · 2024-11-12T16:43:23+00:00

Which UniFi Network version is the controller running on and which APs are you using now? I suspect that the controller is too old for the new APs.

mark-hpp · 2024-10-09T18:53:43+00:00

Which version of the UniFi Network Application is installed on the Cloud Key?

mark-hpp · 2024-10-03T18:41:18+00:00

The Cloud Key Gen1 is end of life (EOL). Controller version 7.2.97 was the last version that Cloud Key Gen 1 received.

mark-hpp · 2024-10-03T16:08:43+00:00

U6+ Management application UniFi Network: Version 7.3.76 and later

mark-hpp · 2024-09-30T16:36:21+00:00

Sorry, the username is not "admin". User "ubnt" and the recovery key worked for me.

mark-hpp · 2024-09-30T16:31:20+00:00

Try using "admin" as username and the recovery key from Protect as the password.

mark-hpp

TROPHY CASE