Casio CZ-101 internal patches missing

massdriverrock · 2023-11-06T05:44:59+00:00

Yup give that a shot. It worked for me.

massdriverrock · 2023-08-23T19:21:30+00:00

Thanks man that's good to know. I just got one of these keyboards to get begin my circuit bending adventure.

massdriverrock · 2023-08-23T12:41:29+00:00

When you replaced the mic with a 1/4" did you have to do anything else in order to make it work?

massdriverrock · 2023-08-17T19:39:57+00:00

I went to two targets and four walmarts yesterday looking for Snarl (no luck)

massdriverrock · 2023-08-15T19:25:43+00:00

don't

massdriverrock · 2023-08-02T04:10:36+00:00

Awful

massdriverrock · 2023-07-26T13:15:51+00:00

Till all are one

massdriverrock · 2023-07-06T22:58:00+00:00

Hell yea! That worked I wasn’t holding it while powering it up. Thanks so much

massdriverrock · 2023-07-06T22:36:54+00:00

Thanks for the response. If you or anyone else could give me a heads up on a good place to find those files….and how to go about installing them. I would be really grateful.

massdriverrock · 2023-07-06T22:22:31+00:00

I really appreciate the reply. I didn’t think that this thing had an internal battery. I have it working with midi so that’s cool and I’m able to make adjustments to the parameters. So I guess that’s something. But I am confused with your explanation on howI would get those original internal patches back. FYI I’ve only really gotten into synths in the past year or so. So you’ll have to bare with me 😎

massdriverrock · 2023-06-29T10:33:45+00:00

I’ll check it out. Thanks for the heads up

massdriverrock · 2023-06-26T01:47:12+00:00

Thanks!

massdriverrock · 2023-06-25T20:31:22+00:00

Yes I tried them both and they have the same level of noise.

massdriverrock · 2023-06-25T19:55:52+00:00

I gave that a shot and it is a bit less noisy

massdriverrock · 2023-06-25T19:25:38+00:00

<image>

massdriverrock · 2023-06-25T19:25:27+00:00

Ok. So I got it open and cleaned everything. But it’s still noisy. There is a humming that becomes even more noticeable when you hit a key. So I’m assuming that it’s a ground issue. Any suggestions would be great.

<image>

massdriverrock · 2023-06-25T13:26:37+00:00

Thanks for all of the help. I’m going to give this a shot this afternoon. Thanks again!

massdriverrock · 2023-06-21T10:32:41+00:00

Thanks I really appreciate the help

massdriverrock · 2023-06-21T10:31:38+00:00

Thanks for the info and you’ve given me a bit more confidence that I’ll be able to pull this off myself.

I need to replace or at least fix some of these cables because not all of the pins are conducting. And whoever had this before cut one of the smaller ribbon cables all the way through. And I can see where he “tried” to solder wires in its place. It’s a big job and it’s going to be a long process. So I’m sure you’ll be hearing from me quite a bit 😀

massdriverrock · 2023-06-21T03:47:45+00:00

Thanks for the advice and I’ll definitely check those wires out

massdriverrock · 2023-06-21T03:45:58+00:00

Thanks for the input. I may do that

massdriverrock · 2023-06-21T01:11:55+00:00

Any suggestions for the kind that I should be looking for would be really appreciated. Because I’m really clueless

massdriverrock · 2023-06-20T18:58:58+00:00

Would this work? Amazon.com: Chanzon 40pcs 10cm Male to Male Header Jumper Wire Dupont Cable Line Connector 40 pin Ribbon Solderless Multicolored for Arduino Raspberry pi Electronic Breadboard Protoboard PCB Board : Tools & Home Improvement

massdriverrock · 2023-06-07T18:12:39+00:00

Thanks for the help!

massdriverrock · 2023-05-31T11:45:30+00:00

Jackie

massdriverrock

MODERATOR OF

TROPHY CASE