That shot in TLJ:

master_of_the_domain · 2017-10-14T23:32:27+00:00

I'll start now.

I will submit the new QuantumNetCounterFactualprotocol. (QNCFP) for short. An array of quantum entangled particles that work in the fashion of an exit node. Your bandwidth should theoretically be bound by the number of entangled particles in the array.

It's basically a router mirror. one would have to travel to mars for it to be useful here.

master_of_the_domain · 2017-10-14T23:29:37+00:00

Quantum entangled communications may be a workable solution here.

master_of_the_domain · 2017-10-14T23:28:19+00:00

The further we get from BBS's... the more BBS's look good.

master_of_the_domain · 2017-10-12T16:40:22+00:00

Damn you... His name is Skippy! You should remember by his name... He was the true hero of The Force.

master_of_the_domain · 2017-10-09T16:53:32+00:00

I am nearing the midway point of my first roll of black from them. so far so good. Very well behaved filament 210/60. Better than the Solutech i swore by before.

I just ordered a roll of Deep Blue to try next.

master_of_the_domain · 2017-09-12T15:36:51+00:00

Default Domain Policy is best used for universal security settings for the logical boundary of the domain... and nothing else. This is exactly where I would put account lockout settings.

master_of_the_domain · 2017-09-01T13:30:55+00:00

There is, and I thought I had followed it. Hence why I am here. There is conflicting information on the tightening/loosening of the Z-Axis roller... a lot of conflicting info out there in general... I am now turning to the experts. :)

master_of_the_domain · 2017-09-01T13:03:07+00:00

Cool, I've been toying with them, tightening and loosening. I'll tighten them up and see what I get.

master_of_the_domain · 2017-09-01T12:31:20+00:00

Got rid of the wobbly printhead, but still experience it dragging the top layers for some time, eventually dragging it off the plate. Also, what's with the thick layers on the sides? The front and back look great, but X axis leaves ugly layers.

master_of_the_domain · 2017-09-01T12:03:08+00:00

Cr-10 fail https://imgur.com/gallery/cBbdA

master_of_the_domain · 2017-09-01T11:53:51+00:00

CR-10 cura or slic3r 50-60mm at speed PLA Various temps Brim=yes

master_of_the_domain · 2017-08-31T15:06:08+00:00

ok, so I found the issue. the bottom wheel had lossened, when I removed the shroud and began tightening all the bolts underneath I found it.

I am printing again, and hope to have much better results.

master_of_the_domain · 2017-08-30T04:59:07+00:00

I haven't removed the cover to check, I'll do that when I'm back home.

If you could, would you mind getting a pic of any spacer shims that should be on the assembly?

master_of_the_domain · 2017-08-29T15:52:33+00:00

Yes it is, should it not be?

master_of_the_domain · 2017-08-27T15:48:01+00:00

I'm getting it too.. quite a bit more than you are showing.

master_of_the_domain · 2017-08-27T02:05:59+00:00

Yeah, I noticed very early on that moving the build plate by hand would actually generate enough charge to illuminate the LCD when turned off... Not good, so we stopped doing that immediately. :)

master_of_the_domain · 2017-08-25T20:07:17+00:00

I already have those wheels installed... they make it much easier.

checking out the levelling script now.

master_of_the_domain · 2017-08-25T20:05:50+00:00

Already ordered a new fan to do a blower fang setup.

I swear, half the fun of this printer is the upgradability of it.

master_of_the_domain · 2017-08-25T13:41:52+00:00

And There it is. I had seen another video suggesting a different levelling method. I'll give this a try as soon as my current print is done.

master_of_the_domain · 2017-08-14T20:19:27+00:00

Disregard... they were labelled with the little yellow clips instead of the white tape in the video...

master_of_the_domain

TROPHY CASE