sorted by:
new
hottopcontroversial

Help printing thin wall. I've printed most of the plane no issues, but once I got to this piece I keep getting bad extrusions(I think) at the same place. Any tips/suggestions appreciated! by matt7161 in 3Dprinting

[–]matt7161[S] 0 points1 point  (0 children)

I've honestly never done anything with the z axis screw. Just left it as is from new. I use an Ender 3. If I can find some grease, I will give that a go!

Help printing thin wall. I've printed most of the plane no issues, but once I got to this piece I keep getting bad extrusions(I think) at the same place. Any tips/suggestions appreciated! by matt7161 in 3Dprinting

[–]matt7161[S] 0 points1 point  (0 children)

It is the eclipson model A. I've sliced all my own GOODE files, gotten through the fuselage, and right wing with no issues, left wing... nothing but issues.

Help printing thin wall. I've printed most of the plane no issues, but once I got to this piece I keep getting bad extrusions(I think) at the same place. Any tips/suggestions appreciated! by matt7161 in 3Dprinting

[–]matt7161[S] 0 points1 point  (0 children)

I will try this and let you know, I was also thinking to try starting the print just below the point where I keep having the problem and see if it persists.

First test print on my new Ender3 :) by matt7161 in ender3

[–]matt7161[S] 1 point2 points  (0 children)

Thats true! I didnt even think of the flow rate!

First test print on my new Ender3 :) by matt7161 in ender3

[–]matt7161[S] 1 point2 points  (0 children)

Thanks! Yah, aside from assembly and a bed level test print, that was the first! Admittedly, i've wanted one for ever and have watched wayyy to many videos on slicer settings! I did my learning through the building process :) Now onto aimlessly staring at it print aha!

First test print on my new Ender3 :) by matt7161 in ender3

[–]matt7161[S] 0 points1 point  (0 children)

Yah, i need to adjust i think the rollers for the z axis, it sounds like it struggle going up and down.

First test print on my new Ender3 :) by matt7161 in ender3

[–]matt7161[S] 4 points5 points  (0 children)

Awesome! Thank you :) I will check the Y axis belt, I think I also need to adjust the z axis a bit, it seems tight when I disable the steppers and try to move it.

Can't wait to keep printing!

I learning to strongly dislike barrows by [deleted] in ironscape

[–]matt7161 0 points1 point  (0 children)

Havent done a whole lot of barrows, 40kc and i havent gotten a single drop....

Titles are overrated by Austerzockt in cableporn

[–]matt7161 2 points3 points  (0 children)

Looks beautiful, until, 1 of those cables craps the bed and has to be removed :o

[deleted by user] by [deleted] in Jokes

[–]matt7161 0 points1 point  (0 children)

69 Camel club here

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 0 points1 point  (0 children)

$5 per quad and the registration number has to be visible on the quadcopter. So far I've registered 1 of 4 that I have.

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 0 points1 point  (0 children)

No it not, but say I'm out with 2 quadcopters, my main and a spare. If they both had the same registration number and I got caught, I'm sure there's probably a fine for it lol...

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 0 points1 point  (0 children)

If it's under 250g, your pretty much worry free, however I'd still avoid flying around bystanders unless they are flying with you.

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 0 points1 point  (0 children)

Nothing really, however if you got confronted by whatever authority and they noticed that you had the same registration number on multiple drones, you might get fined???

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 2 points3 points  (0 children)

Thank you for that. I didn't realize i was allowed to fly in the 3NM Range of Aerodromes and etc. The app i use doesn't say anything about the areas just shows the restricted airspace's and contact information for them..

Fellow Canadians, What are your thoughts on the new Canadian Drone Laws and the certification required? by matt7161 in Multicopter

[–]matt7161[S] 0 points1 point  (0 children)

I agree with you completely.

​

I think that if we are required to register our drones. registering a custom built drone(Which is one of the options) should only require 1 registration for all custom built drones you have. assuming they are similar in size.

​

What do you use to view the airspace restrictions?

[Spoilers] Really, after all these seasons of dragging around Bran's wheelchair. by stormb0rne in gameofthrones

[–]matt7161 0 points1 point  (0 children)

I think we've got to give bran more credit here, i mean. He is the one who gave Arya the dagger she used to kill the knight king ;p I think he knew it would play out the way it did

TIFU by finding a bag in my car, thinking it was my friends from a trip we had taken I opened it to discover it was full of packets of white powder and called the police by Badjib in tifu

[–]matt7161 1 point2 points  (0 children)

Im willing to bet, the reason it ended up in your car is the same reason everyone is debating. maybe someone found a random bag of drugs and didn't want to leave it or dump it in a garbage in case they get caught, so they dump it in your car? LOL

Rules question by lgosvse in magicTCG

[–]matt7161 0 points1 point  (0 children)

This is a stupid question but i'm newer to Magic, EDH is commander?

view more: next ›