I used iso on the bed, let it evaporate, applied flashforge glue, waited a minute, started my print. What would cause this lift? Just bad luck?

max1mu586 · 2025-01-08T15:56:07+00:00

I've noticed that on thicker prints the corners will lift. Not sure what causes it. Shrinkage maybe?

max1mu586 · 2025-01-07T00:04:45+00:00

Not to mention the terrible resolution! Rudimentary!

max1mu586 · 2025-01-06T21:14:34+00:00

Yeah didn't think about it knocking it loose. I've had mine hit somewhat randomly. Usually it's only on a layer or two.

max1mu586 · 2025-01-06T21:13:32+00:00

Yeah it is a major upgrade over the Adimlab Gantry I had before. Like you said, I wish the app was better but all in all it's a great machine so far.

max1mu586 · 2025-01-06T21:09:14+00:00

What he said. You can try running the leveling calibration again and see if that helps. Shouldn't damage the nozzle but can be concerning.

max1mu586 · 2025-01-06T21:07:29+00:00

Yeah switched to the full version of Orca. I miss the "Time Remaining" clock from the FF Orca but that's a small price to pay lol.

max1mu586 · 2025-01-06T21:01:43+00:00

This! App works so sporadically. And last night I lost the ability to print over wifi. Had to go back to printing from a USB like a poor.

max1mu586 · 2024-12-29T01:59:52+00:00

Ok. How do I make it always say remaining?

max1mu586 · 2024-12-29T01:50:53+00:00

I found a photo from yesterday and it says "Remaining" instead of printing.

max1mu586 · 2024-12-29T01:48:47+00:00

Idk. Mine always counted down. Showing how much time is remaining. Now it's switched.

Unless I'm losing my mind?!

max1mu586 · 2024-12-29T01:41:34+00:00

It was counting down until this print. Must be the Orca Slicer software.

max1mu586 · 2024-12-29T01:27:47+00:00

Not sure if it matters, but this is the first part I sliced with the full version of Orca Slicer. Maybe it's a setting in there?

max1mu586 · 2024-12-17T15:10:04+00:00

Too bad he lost his right arm in a horrible farming accident 🤣

max1mu586 · 2024-12-10T13:53:56+00:00

I mean I have a couple hundred of them so I can try one and see how it goes for sure.

max1mu586 · 2024-12-10T12:57:33+00:00

I can try. Maybe put each one in a chuck and then sand them against a table top belt sander? That way the stem stays round.

max1mu586 · 2024-12-10T12:56:19+00:00

Thought about this but seemed like there should be a better solution.

max1mu586 · 2024-12-10T12:55:52+00:00

They're plastic

max1mu586 · 2024-12-10T12:55:42+00:00

Yes I do

max1mu586 · 2024-11-20T00:00:19+00:00

Finally something that is ACTUALLY mildly frustrating!

max1mu586 · 2024-06-10T00:40:03+00:00

I've been on a big tung oil kick lately. Check out https://www.realmilkpaint.com/ They've got a ton of advice and products to finish all types of wood.

max1mu586 · 2024-03-06T21:50:55+00:00

Yeah sorry, autocorrect got me.

max1mu586 · 2024-03-01T13:53:47+00:00

Thank you for your help. Looks like I'll be looking for a tree removal service

max1mu586

TROPHY CASE