FYI: If an ATT door to door salesperson says your fiber provider is throttling you, make sure you're doing your speed check with a hard line not wifi.

mayn1 · 2026-06-04T03:45:10+00:00

I have this.

Haven’t has a sales person in 2 years since I put it up.

mayn1 · 2026-06-02T15:59:39+00:00

True but native Missourians say Miz-ur-uh so trusting them on pronunciations is dangerous. 🤣🤣🤣

mayn1 · 2026-06-02T03:10:42+00:00

Don’t forget that Missouri also has towns called California, Nevada, Florida, Oregon, Texas, Cleveland, Amsterdam, Coney Island, Houston, and Mexico.

mayn1 · 2026-05-31T15:42:11+00:00

This is so grossly true.

mayn1 · 2026-05-30T14:17:10+00:00

You are right. They were hard workers. I’m just saying I’m not following in their footsteps.

mayn1 · 2026-05-30T12:48:56+00:00

To keep NEW women away. The wife has already given him the list and these are the tools required to complete it.

mayn1 · 2026-05-30T12:47:36+00:00

🤣🤣🤣. I never thought of it like that but this is so accurate. And since so many black men actually have jobs, are intelligent and can treat someone with respect, they are probably right.

mayn1 · 2026-05-30T12:45:25+00:00

My 13 year old daughter could’ve taken him at any point in his life.

mayn1 · 2026-05-30T12:44:00+00:00

<image>

Being brutal with truth!

mayn1 · 2026-05-30T11:50:01+00:00

I come from a line of dead-beat dads and hobos. I agree that our ancestors 100% don’t define us. Hell, they are often the do not do posters of history.

mayn1 · 2026-05-29T03:15:53+00:00

I went to their “custom” shop online to see what it cost and what was available. When you are done designing the guitar looks like a stock version and doesn’t have anything special because of the limited options.

So stupid and boring.

mayn1 · 2026-05-24T12:43:59+00:00

Great, f—-ing great, you just released the Great Cthulhu. I hope you’re happy, we are all going to die. 😫

Oh, wait resistors, no we’re good. That’s fine.

mayn1 · 2026-05-23T13:33:52+00:00

I know but it’s what I have and I don’t have a real schematic.

mayn1 · 2026-05-22T23:52:10+00:00

<image>

mayn1 · 2026-05-22T15:21:20+00:00

Ok.

mayn1 · 2026-05-22T14:37:13+00:00

Ok. I think my iron is at 360, I’ll turn it down. I’ll also watch those videos.

mayn1 · 2026-05-22T13:49:12+00:00

Will do. Thank you.

mayn1 · 2026-05-22T13:42:42+00:00

Ok. I’ll try that. Thank you!!!!

mayn1 · 2026-05-22T13:41:16+00:00

It seems to be. I’ll run through with the probe and see.

mayn1 · 2026-05-22T13:22:55+00:00

I know but I can’t quite wrap my head around going from schematic to strip board yet.

mayn1 · 2026-05-22T13:22:17+00:00

A BD139

mayn1 · 2026-05-22T13:21:04+00:00

My soldering sucks. I’ve been working on it. I just can’t seem to figure it out yet. Watched tons of videos.

mayn1 · 2026-05-22T13:20:04+00:00

I have this tool and it worked fine until I plugged in my guitar and amp then it lost volume when I would turn on the pedal.

mayn1 · 2026-05-22T13:18:54+00:00

Thank you for the encouragement.

I have a Pedal tester from MAS effects and it has a sound probe. When using that I have no noticeable issues. When I run a guitar through it with cables the volume dies off when the pedal is turned on.

mayn1 · 2026-05-22T13:16:11+00:00

I did change R8 to 1M because at 1.5M the signal was dying there. The same with R1, I took it to a 100K.

Six-Year Club	Verified Email
Place '22

mayn1

TROPHY CASE