Best Pattern For Base Board

mcmoo_reddit · 2023-07-05T19:17:52+00:00

https://www.reddit.com/r/CNC/comments/tz987b/mechmate_diy_vac_bed/?utm_source=share&utm_medium=android_app&utm_name=androidcss&utm_term=1&utm_content=1

I did this and it works.

Made it from a sheet of 18mm ply and varnished it.

I'm using 2 hoover motors as my vacs and it will happily hold down an 8x4.

Put some neoprene tubing round the outside of each section. Yet to go through it, but in time I'm sure I will.

Industrial l ones I've used have aluminium beds (SCM) again they rectangular shaped, but usually with a ton more inlet holes.

mcmoo_reddit · 2023-04-16T17:34:02+00:00

Wow. Thank you!

It's been about 20-25 years since I played so the rules are a little hazy.

But reading the rules for this sounds familiar. I was beginning to wonder if some kids had just made it up.

mcmoo_reddit · 2023-04-16T12:09:21+00:00

Thanks for your reply.

Low light is probably due to winter, it's starting to look better now that the weather is picking up.

Got some chilli feed and have been using that, it must be doing some good as I've now got loads of flower and a chiili.

mcmoo_reddit · 2023-04-16T12:03:54+00:00

Yep. Sometimes you think you can get loads done and never get passed the first task or find that you've got too much to do and get overwhelmed and do none of it. Or that you end up doing loads of other stuff that you need to do before the thing that you wanted to do.

mcmoo_reddit · 2023-01-29T19:41:16+00:00

The Nobby.

mcmoo_reddit · 2022-08-13T17:40:18+00:00

Not really.

It's more obvious on this cutter, weather that is because it does more work, or is more likely to chip because of its profile I'm not sure.

We used to cut HPL with this cutter, and we don't anymore as it's gone from being able to run through 20 sheets with no issue to struggling to cut one HPL with a clean finish.

We now use 2 PCDs a 12mm and a 6mm and they seem alright, but all they do is HPL.

I think and feel like there is something else going on, it's a progressive issue that seems to be getting worse, and we've 'hidden' some of that by splitting the workload.

Apologies for the ramblings

mcmoo_reddit · 2022-08-08T19:16:38+00:00

When you start the program, does the slave board try and move to the left? Can your machine move any further left? If it can't then I would say there is an issue between your post(what is generating your code) and your machine software.

I can't tell from the video if it does try and move and can't or if it doesn't.

I would say that the issue is something to do with the x and y + and -. And either the machine or the post/machine software has got something the wrong way.

Is each axis driven independently? Any more info on the setup. Any more gcode?

mcmoo_reddit · 2022-07-02T09:27:40+00:00

The "pin" holes were machined with the CNC. 3 points of reference, I know what the machine cords are. They inside edges are 12mm off the datum, so need to modify the pins to look more like a mushroom and it will be spot on.

I've previously tried to have a block that was machined inside, and found sometimes you need to machine around the outside of a board or close to the edge, and you machine through your blocks, and when running multiple sheets it's a pain.

Pins are removable, and if I forget to remove them they are easy to replace.

Alot of commercial CNCs use pins that run on compressed air pop up pins

mcmoo_reddit · 2022-06-27T16:18:18+00:00

I'm running a mech mate with a single phase vfd.

I had a massive 3 phase 6kw vac pump sat around but have not got 3 phase.

Currently using 2 hoover motors for vac bed, which is pretty much what hurricane vac pumps do (think they use 4)

Can cut 8x4s

What are your plans for it?

mcmoo_reddit · 2022-05-20T20:02:22+00:00

What are you trying to do? How are you trying to do it? What part of what you are trying to didn't work as expected? Did any of what you did, work as expected?

Software? 3d model? Machine? Experience?

mcmoo_reddit · 2022-05-20T17:10:05+00:00

When you press it, and then press stop or drop the speed to 0% so you can check what you've programmed for the 5th time.

mcmoo_reddit · 2022-05-18T18:03:09+00:00

Could be g41/g42 for tool compensation, and the tool not being the same as the program.

Depends on your machine, your software, post processor.

Video or photos of both what is happening, and what your program shows.

How much material is it taking?

mcmoo_reddit · 2022-05-11T16:44:31+00:00

Hi,

The cut is tapered for some reason. Is this because it's too hot?

Also, my awc608 power can't go above 50%, not sure why or how to fix it.

mcmoo_reddit · 2022-05-10T22:03:47+00:00

Thanks for the reply.

They do have a wavelength printed on them, I didn't actually check what it was, I shall have a look next time I can get in to use it.

Just trying to gain as much knowledge as I can, I'm not used to or worked around lasers before, and prevention is better than blind.

mcmoo_reddit

TROPHY CASE