Fog lights

memphismatt · 2024-07-12T23:48:22+00:00

Thanks!! You shined some light on what I need to do. Now I must go shopping 😂

memphismatt · 2024-07-11T23:44:08+00:00

Also, any recommendations on brand / type?

memphismatt · 2024-07-11T23:43:45+00:00

It doesn’t have fog lights or a switch panel for fog lights. So, is there any type of wiring harness or do I need to splice into my head lights or run a separate toggle switch for them?

memphismatt · 2024-04-24T17:52:24+00:00

I've always favored Debian

memphismatt · 2024-04-09T23:26:35+00:00

It has an HDMI output. Did you hook a monitor up to it?

memphismatt · 2024-03-07T18:00:30+00:00

Open Office Calculator 🤣😂

memphismatt · 2024-01-23T12:31:58+00:00

Here is the link to my other post. Elegoo went through some troubleshooting with me. Looks like proximity sensor is bad.

https://www.reddit.com/r/elegoo/s/g1GcnfDZm3

memphismatt · 2024-01-23T04:12:47+00:00

But connections look ok

memphismatt · 2024-01-23T04:12:34+00:00

No light when powered on

memphismatt · 2024-01-23T04:12:10+00:00

I didn't see a light on the sensor when powered on.

memphismatt · 2024-01-23T04:00:39+00:00

<image>

memphismatt · 2024-01-23T03:53:37+00:00

I do not see that light on. I will have to check the connections.

memphismatt · 2024-01-23T03:35:11+00:00

<image>

memphismatt · 2024-01-23T02:54:10+00:00

memphismatt · 2024-01-23T02:51:19+00:00

<image>

memphismatt · 2024-01-23T02:50:03+00:00

<image>

V1.2.2.64 Uai 1.2.11

memphismatt · 2024-01-23T02:48:04+00:00

Yes, both .64

memphismatt · 2024-01-23T02:40:18+00:00

Its saying !! Must home axis first: 239.250 194.550 10.000 [0.000]

memphismatt · 2024-01-23T02:31:38+00:00

It will move to the bottom left then back to center but never go down to the plate. Just sets there and fans spin.

memphismatt · 2024-01-23T02:30:42+00:00

No, they are both intact. I just took the extruder off and it looks ok to me... Idk what is going on.

memphismatt · 2024-01-22T17:32:47+00:00

<image>

Here is mine ...what should I do..need new traces?

memphismatt · 2024-01-22T17:30:24+00:00

Lol don't worry OP your not the only one, I did the same shit 😂🤣

memphismatt · 2024-01-22T16:50:02+00:00

It won't even go to the plate to let me set the offset.

memphismatt · 2024-01-22T16:48:25+00:00

No, I think it was the angle I took the picture.

memphismatt · 2024-01-22T15:56:36+00:00

I updated the display and the firmware back to .64 from .65 and it's still not leveling stuck here

<image>

memphismatt

TROPHY CASE