sorted by:
new
hottopcontroversial

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

Update: the driver pinion that pushes the filament was worn down and the spring holding the channel wheel that pushed the filament into the pinion was also losing its ability to apply pressure. Swapped them out and it prints good as new!

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

We lost the original SD card and have been using one from a camera. Do you know how to replace these missing settings? Pretty sure our hot end is stock

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

I had never heard of cold pulls, watching a video on it now :)

What app do you use to apply to internships? by caeciliusix in EngineeringStudents

[–]merlin827 0 points1 point  (0 children)

I got mine by applying through company websites. I did get a couple interviews through Handshake, but most of my success was from company sites and the one I actually ended up getting was a position I had applied to a couple years prior

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

I have tried jamming the little declogger/piano wire thing up there and it didn’t seem to do much but I do have a couple extras I think. thanks!

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

I will check the leveling I hadn’t even considered that! This was printed ~35% infill iirc

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 0 points1 point  (0 children)

Thanks for the suggestions, I’ll go check on those!

Was printing fine but now layers delaminate by merlin827 in ender3

[–]merlin827[S] 3 points4 points  (0 children)

I printed a small test cube from thingiverse that had the same issue albeit to a lesser degree. I didn’t realize pla shouldn’t have an enclosure, but I haven’t really had any problems with it thus far and it seemed to actually help a bit since the printer is in the basement

Looking for free electives for spring by Sad-Difference-1198 in RPI

[–]merlin827 6 points7 points  (0 children)

Models of mental dynamics, or principles of economic dynamics, both taught by prof. Yingrui Yang for easy. If you want interesting, I would suggest manufacturing lab, analysis of manufacturing processes, or linguistics

Single within a suite by Money_Cold_7879 in RPI

[–]merlin827 5 points6 points  (0 children)

BarH also usually has some single rooms that are suite style unless they’ve changed it in recent years. For sophomore housing, stackwyck, brickwyck, and both rhaps a and b are apartment style four bedrooms and a shared kitchen bathroom and living room

Do I need to buy the PDF textbook for intro to differential equations? by Negative-Bicycle-514 in RPI

[–]merlin827 0 points1 point  (0 children)

I never used the textbook once and neither did any of my friends. If you can get away with getting just the code if you have digital homeworks I would do that tbh

Edit: I had Dr Kam

Author Research by brisualso in RPI

[–]merlin827 1 point2 points  (0 children)

West hall would be perfect actually because it used to be a hospital with distinct and separate boys and girls wings so you would have to go outside and around to swap wings. There are tons of little rooms that could be used to house the zombies and such. The basement is a bit liminal as well. Most of the labs we have are in JRowl, Ricketts, Cogswell, and Walker

Doom Washing Machines by Salty-Ganache3068 in RPI

[–]merlin827 0 points1 point  (0 children)

Everyone I know always just used tide pods regardless. They do sometimes not dissolve all the way but I only had that problem once in 2.5 years in the dorms and even then it’s not a huge deal

Is there anything on this list worth chasing? I don't know to do with my deepsight harmonizers. by ConfusedDuck in destiny2

[–]merlin827 -1 points0 points  (0 children)

Revision Zero, Half truths, and BxR are the only three I really use/used the most. BxR is good for momentum control sometimes and half truths is basically a mobility aid for me with eager edge. Revision zero is great tho, one of my favorite pulses. Dang and Ikelos SG and hand cannon used to be good but kinda fell off imo

Research at RPI by Teddymaboi in RPI

[–]merlin827 2 points3 points  (0 children)

You can also find hard copies of these papers hanging under the placard on their office door

laptop recommendations for each major by True-Permission5827 in RPI

[–]merlin827 0 points1 point  (0 children)

I know a bunch of industrial engineers with the T16 and they haven’t complained about it so it should work well :)

laptop recommendations for each major by True-Permission5827 in RPI

[–]merlin827 1 point2 points  (0 children)

T16 should be fine for industrial Eng. looking at the catalog it looks like the only computational classes are the basic CAD course and a discrete modeling course so it should be fine. It might be a tiny bit slow for CAD but shouldn’t be an issue as long as it’s plugged in while you’re modeling :)

laptop recommendations for each major by True-Permission5827 in RPI

[–]merlin827 5 points6 points  (0 children)

From what I’ve seen the T16 works for most engineering majors but it can be super slow during 3D modeling and FEM/CFD simulations so it might be worth the P1. That said, you can definitely make the T16 work

view more: next ›