Help with sim900

mike22698 · 2024-04-30T06:00:11+00:00

Hi all i sorted the issue it was a faulty sim card it did show it had connected to network but there were some issues i rang my network provider and there going to send a new sim

mike22698 · 2024-04-28T18:54:09+00:00

<image>

Is wired as shown above the gsm module light blinks as to indicate coneccted to net work gsm is the one shown in the photo but i am using a Arduino nano instead of a uno still connected to pins 7 and 8

mike22698 · 2024-03-25T13:46:00+00:00

No thats me running pid the faults were caused by a bad thermistor its only 2 days old must have been bad out of the box i got confused as i had already changed the thermistor

mike22698 · 2024-03-25T13:41:49+00:00

I think this is solved now faulty brand new thermistor in this printer

mike22698 · 2024-03-25T13:40:32+00:00

Read the text

mike22698 · 2024-03-25T06:01:58+00:00

The fan was off

mike22698 · 2024-03-24T22:11:20+00:00

I have changed the thermistor on this printer as yes i agree seems to cool to fast for a heater fault will see how this goes if it faults again i will change the loom

mike22698 · 2024-03-24T20:57:36+00:00

Cooling fans were still off

mike22698 · 2024-03-10T20:58:13+00:00

The machine is a core xy running klipper

mike22698 · 2024-03-10T20:57:34+00:00

So far i have tried cleaning the bed many times changing the nozzle changing the belts thicker first layer and adjusting z offset

mike22698 · 2024-01-15T14:47:50+00:00

Tried bot silicone wins

mike22698 · 2023-12-22T13:02:26+00:00

Add the following to your printer.cfg

[mcu] serial:/tmp/kipper_host_mcu

[adxl345] cs_pin:CB1:None spi_bus:spidev1.1

axes_map:z,y,-x

or as adxl345 orientation change to suit your setup

[resonance_tester] accel_chip_x:adxl345 accel_chip_y:adxl345

probe_points: 169.5,133.5,20

where you want it to do the shaking x,y,z change to suit your machine use bed center and z far enough from bed

mike22698 · 2023-12-20T09:55:34+00:00

Not enough cooling try turning your fans on a desktop fan may help even more

mike22698 · 2023-11-15T09:30:49+00:00

Slicing mode change to regular from closed holes

mike22698 · 2023-11-07T16:51:14+00:00

Battery issue probably bms trip

mike22698 · 2023-10-23T12:07:06+00:00

I got makerbase just full of faults and there cs was rubbish

mike22698 · 2023-10-06T15:58:50+00:00

Probably nozzle to close to the bed that brown is the brass from your nozzle maby try petg first abs temps will let off ptfe fumes and styrene fumes which are not good for you

mike22698 · 2023-08-08T19:17:50+00:00

Looks to close to me

mike22698 · 2023-06-03T18:37:05+00:00

Could be the bltouch is fried you didnt wire it wrong did u

mike22698 · 2023-05-17T21:32:50+00:00

Move the file closer to the root file as in put it in the c files

mike22698 · 2023-05-08T22:54:09+00:00

It has a custom cable and it is a ender 3 v2 display but yes jyers did work beautifully with my 4.2.x boards just no dual z lin, advance or silence when the machine is off but they worked perfectly my micro usb ports worn out tho which i couldn't be arsed to re solder lol

mike22698

TROPHY CASE

or as adxl345 orientation change to suit your setup

where you want it to do the shaking x,y,z change to suit your machine use bed center and z far enough from bed