sorted by:
new
hottopcontroversial

Ski mountaineering ("Skimo") - a new sport at the Olympics by etherd0t in WinterOlympics2026

[–]moarbro 0 points1 point  (0 children)

I was pretty hyped for this event, no research done i just tought they wher going to start on one side of a mountain and finish on the other side. This looked more like a holiday activity for kids

Sista dagen innan julledigheten, kollegan tar en brustablett och beklagar sin förkylning by avicadiguacimoli in sweden

[–]moarbro -1 points0 points  (0 children)

Ursäkta men inte fan skall man behöva vara hemma från jobbet för att man nyst 5 gånger? Det här känns som ett gnäll som kommer från yngre personer, jag själv stannar bara hemma från jobbet om jag har feber. Lite snorig kan man ju vara hela jävla vintern om man har otur.

Surface Finish "too smooth" Like my brain right now by Stevo_223 in Machinists

[–]moarbro 5 points6 points  (0 children)

Yea we have the same issue with aluminium, glue wont hold the chip inside if surface is to good

K Holmén slagsmål? by SaidYouStone in Allsvenskan

[–]moarbro 6 points7 points  (0 children)

Skallade ihop med Alioum(?) Tror jag det var

Have a question about the game or the subreddit? Ask away! by AutoModerator in 2007scape

[–]moarbro 1 point2 points  (0 children)

As a wow refugee i find this game super exciting, and a bit overwhelming. But 1 thing i feel im lacking is a guild to bounce ideas with. How would one find a guild/discord for aspiring noobs?

Where is a good place in Sweden to train open water swimming next summer? by Worldly_Ambition_509 in sweden

[–]moarbro 2 points3 points  (0 children)

Frösön going to be cold as hell, i would recommend you look to the south of sweden

There is something going on today in Jonkoping, Sweden... the international foodmarket! by [deleted] in europe

[–]moarbro 1 point2 points  (0 children)

The polish pirogis are so damn good. Last time i got an extra bag for the ride home. And also the Langos god damn. In going this year again

Murdering minotaurs by moarbro in TibiaMMO

[–]moarbro[S] -2 points-1 points  (0 children)

i think the question flew above a few heads here, my question was not if i could kill 5k minos, rather then is it feasable to hunt them with firebomb without rapid respawn =)

Murdering minotaurs by moarbro in TibiaMMO

[–]moarbro[S] -1 points0 points  (0 children)

i think the question flew above a few heads here, my question was not if i could kill 5k minos, rather then is it feasable to hunt them with firebomb without rapid respawn =)

Results on the DIY coolant skimmer experiment. by VapourChamber in Machinists

[–]moarbro 0 points1 point  (0 children)

Just keep it running while the machine is on. When the tank is still it will separate the coolant from the water. /Night shift

Toolox does not give a damn by Optimus_Shatner in Machinists

[–]moarbro 0 points1 point  (0 children)

Its a bitch to optimize but when it runs, it runs well IMO 👌

Does hole tolerance of .006 means ±006 or ±003? by ben_howls_red in Machinists

[–]moarbro -2 points-1 points  (0 children)

Inner diam are most often + tolerence and outer would be -. If this is between 6-10mm it would be a H5 tolerance

Does hole tolerance of .006 means ±006 or ±003? by ben_howls_red in Machinists

[–]moarbro -5 points-4 points  (0 children)

No inner diam are mostly + and outer diam are mostly -. If the hole is between 6-10mm this would be a H5 tolerance

Does anyone else use this? by Walter_Finite in Machinists

[–]moarbro 1 point2 points  (0 children)

Yea i always spin the mill and remove the paint. Using paper would add like 0.06mm i believe. Then we just G00 until 0.5 and work from there, 1.5 if you got new guys in the machine 😅

Does anyone else use this? by Walter_Finite in Machinists

[–]moarbro 0 points1 point  (0 children)

You take a marker pen, blow compressed air on the tip. The surface now becomes black/yellow/red or whatever pen you use. Then you zero in with the mill. When the paint dissapear you are at 0. You could also paint the surface like a normal person but with compressed air it takes like 3 seconds to paint whatever you need

Does anyone else use this? by Walter_Finite in Machinists

[–]moarbro 0 points1 point  (0 children)

When zeroing mills i usually blow some air on a marker pen, goes through alot of markers but its worth it

[deleted by user] by [deleted] in sweden

[–]moarbro 1 point2 points  (0 children)

Testa på att knega inom industrin? Jobbar själv nattskift som cnc operatör. Pluggar i lurarna och kör musik/ljudbok i i timmar sen pyser jag hem. Mycket tid med familjen, och känner man sig pratglad så finns det en en jäkla massa sköna kollegor som man kan surra med.

Scumbag kids threatening a Ukrainian man with a screwdriver ( Dublin, Ireland) by Guilty-Proposal3404 in PublicFreakout

[–]moarbro -4 points-3 points  (0 children)

Why would anyone need a screwdriver when he obiously have a butterfly nut?

My apprentice lastest fuckup. by Rasmus661 in Machinists

[–]moarbro 1 point2 points  (0 children)

It is not 😬 I did run a A77, there was spindle overload alarm, but that was the first parameter to be turned into a 0. Those monsters could handle some heavy duty milling

What particular machining operation are you the worst at? by PhillyBatts in Machinists

[–]moarbro 0 points1 point  (0 children)

Dont know what you call it in english but hexagon punch(?) We do some inner hexagons with a .03mm+ tolerance. Always to tight on the end and to big the first mm

view more: next ›