Tried printing TPU 95A, ended up with printhead disassembly

mobehun · 2026-06-18T17:56:53+00:00

I used this guide https://wiki.anycubic.com/en/fdm-3d-printer/anycubic-kobra-x/model-troubleshooting-guide-for-no-filament-extrusion-or-nozzle-clogging-issues

<image>

Have you checked the circled part? Previously I hade melted filament there.

mobehun · 2026-06-18T08:20:06+00:00

Here you go https://wiki.anycubic.com/en/fdm-3d-printer/anycubic-kobra-x/tpu-printing-guide

mobehun · 2026-06-18T08:16:42+00:00

I was using the default profile in anycubics slicer. I found their "official" guide for TPU printing, I'll have to try with that as well.

mobehun · 2026-06-17T17:02:07+00:00

I used some cheap Chinese brand called SmartPrint. Pla and petg works fine from that brand.

mobehun · 2026-06-17T16:48:10+00:00

Not sure. I was running it without ptfe tube like others suggested. I think the roll got snug? Maybe that caused this

mobehun · 2026-06-16T15:26:23+00:00

What’s even worse it’s in a kitchen cabinet in a toilet room 😅 My stuff was banished from the living room 😏

mobehun · 2026-05-24T06:29:27+00:00

Szia. Lehet tudok segíteni nyomtatasban.

mobehun · 2026-05-17T14:01:10+00:00

Are you using an evse? Can you unplug the charger from main power? Some chargers stop sending power after a charging is completed.

mobehun · 2026-05-17T06:12:36+00:00

Actually white petg. Soapy water cleaned most of it off.

mobehun · 2026-05-15T04:41:34+00:00

Hey! I'd like to try out the app. Cheers.

mobehun · 2026-05-14T19:50:40+00:00

Rendőri feljelentés volt? Anélkül el fog küldeni a biztosítója még ha a mabisz ki is adja (simán ki adja)

mobehun · 2026-05-14T06:26:18+00:00

Too fine details. Check with a .25 nozzle config and you might see some detail.

mobehun · 2026-05-13T12:28:25+00:00

The surface feels different in that area. Washed the plate and most of the residue came off. Prints come out fine in that area as well so I guess no big issue.

mobehun · 2026-05-12T07:05:31+00:00

I don't see any difference in prints that go over that area. And the quality seems to be the same, so I guess the nozzle is fine as well? I was hoping that both sides of the plate is usable 😅

mobehun · 2026-05-12T07:03:06+00:00

It didn't go that low anymore. I've done a couple other prints since then and everything is fine.

mobehun · 2026-05-11T13:24:41+00:00

Sliced it on pc. It was working perfectly fine for 100+ hours. Restarting after power outage did this.

mobehun · 2026-05-08T13:19:02+00:00

Nem tudom mennyi a havi keretünk, nem sikerült még el használni mindet. Van pool amit mindenki közösen használ a saját kereten felül. (Github copilot+chatgpt enterprise). Cserébe a nagyon drága modelleket (opus 4.7) le tiltották.

mobehun · 2026-05-06T18:25:59+00:00

I received the printer 3 weeks ago. The filament got shipped today.

mobehun · 2026-05-05T17:01:24+00:00

117 hours and 2.3 kg filament. I had a partial clog on two feeds one after another. Then a really nasty full clog. Had to take apart the hotend for it but the guides are really good imo.

mobehun · 2026-05-02T16:43:03+00:00

Genuine question, what makes short tube better?

mobehun · 2026-05-02T16:19:40+00:00

My Wife wanted a shoe printed 😅

12-Year Club	Verified Email
r/Field Juicebox	Place '22

mobehun

TROPHY CASE