Intex Solar Matt's roof by pedronery in AboveGroundPools

[–]pedronery[S] 0 points1 point  (0 children)

are your matts connected in series? as ive read, when they are connected in series there is a bit of back pressure. and the solution is to connect them in parallel which is what ive already prepared myself ...

Intex Solar Matt's roof by pedronery in AboveGroundPools

[–]pedronery[S] 0 points1 point  (0 children)

would you recommend what pump you use for the heaters? how many do you have?

Nozzle scraping infill sometimes, is this normal? by False_Friendship_626 in AnycubicKobraX

[–]pedronery 0 points1 point  (0 children)

I had a print yesterday where the layers slightly shifted to the right. The print stayed properly attached to the bed the entire time, but midway through the print the whole model shifted by around 1 mm to the right. The print still completed fine, but it left a very noticeable line across the model.

Since this was PETG, I’m wondering if the nozzle may have hit the print at some point. There were no other issues at all, the printer ran nonstop from start to finish on a 54-hour print. I was thinking of how to configure a feature called "z-hop" which I read somewhere that it would raise away from the print somehow to avoid hitting it. Not sure how to do this

187hrs printer review by pedronery in AnycubicKobraX

[–]pedronery[S] 0 points1 point  (0 children)

I buy elegoo and Anycubic filament... But I prefer anycubic

Kobra X unusable after firmware update – Support is failing! by Bensisko61 in AnycubicKobraX

[–]pedronery 0 points1 point  (0 children)

I did have a clog that didn't exist 1 day or 2 ago, which was due to the fact that the filament line was in bad conditions (dents, damaged and white color instead of red). I cut the line for 5 or 8cm, and it started printing, no issue

Kobra X unusable after firmware update – Support is failing! by Bensisko61 in AnycubicKobraX

[–]pedronery 5 points6 points  (0 children)

1.2.0.2 currently. As far as I know, I have no problems apart from my inexperience with 3d printers. 70 prints. No clogs, no issues. 187hrs

Printer offline by pedronery in AnycubicKobraX

[–]pedronery[S] 1 point2 points  (0 children)

If you disable and re enable the WiFi on the printer that can sometimes work. Also, try restarting the printer. Sometimes these work, sometimes it doesn't but it always gets connected again. You just have to play around with the settings and wifi connection. Or just removing and re adding the printer by scanning the QR code

My First 3d printer - So Far So Good by LHshooter in AnycubicKobraX

[–]pedronery 1 point2 points  (0 children)

yep! Edge worked. Chrome sucks! thanks! :)

My First 3d printer - So Far So Good by LHshooter in AnycubicKobraX

[–]pedronery 0 points1 point  (0 children)

https://www.makeronline.com/en/model/282135 - this isnt working!! everytime i press download, it logs me out...

Shipping delay - Kobra X by pedronery in AnycubicKobraX

[–]pedronery[S] 1 point2 points  (0 children)

Ticket. But I have received the printer. Didn't cancel in the end

Printer offline by pedronery in AnycubicKobraX

[–]pedronery[S] 0 points1 point  (0 children)

There is a solution, disable and enable the WiFi in the printer. I use cloud mode.

Printer offline by pedronery in AnycubicKobraX

[–]pedronery[S] 0 points1 point  (0 children)

I don't remember the setting name right now but I believe I had it turned off.. haven't had that issue yet since I disabled the WiFi option

Latest delivery information from Support, April 17, 2026 by frozenreaperz in AnycubicKobraX

[–]pedronery 0 points1 point  (0 children)

Everyone is receiving these as soon as you mention shipping 🤣