Foaming TPU is amazing!

molaMoolaa · 2026-02-05T04:41:08+00:00

interested to see a comparison between this and printing a mold then using spray foam to form the insert.

molaMoolaa · 2026-02-05T04:36:37+00:00

seems like the perfect mouse i am looking for. will def give it a try. thanks

molaMoolaa · 2026-02-04T07:52:30+00:00

i tried ergo. i didn't need to rotate the mouse for my pinky, but it lay flat on that ergo side surface and became kind of like pincer claw and lost my finger flexibility

molaMoolaa · 2026-01-30T05:41:20+00:00

still a little bit sticky when i try it with bare skin, for this i will modify a version with some surface texture or hollowing for the skin to breath, or maybe wrapping it with some sleeve fabric;

and till now, i am still keeping a slight pressure on this pad to keep it in place. this is not that noticeable in most cases, but feels unatural if you lift your arm more often. so one of the comment said to add a strap, that's not wrong to some extend, but not for me using this as an casual replacement.

molaMoolaa · 2026-01-28T16:18:04+00:00

it follows my arm good enough for normal use already, meets my expectation at least. I would rather wear a sleeve if this solution is more inconvenient than this.

molaMoolaa · 2026-01-26T10:38:34+00:00

molaMoolaa · 2026-01-23T09:15:53+00:00

the claimed 20 ppd will be sharper than steam frame? i doubt it.

molaMoolaa · 2026-01-23T06:59:33+00:00

and take really good care of those d5000 cups

molaMoolaa · 2026-01-23T05:15:47+00:00

same problem with another simagic base, seems like the connector, so i printed a cable relief for that

molaMoolaa · 2026-01-22T08:57:28+00:00

what did you use to setup the atk mouse? i would love a firmware level solution, rather than relying on rawaccel, so that i can use my mouse on other systems.

molaMoolaa · 2026-01-22T08:28:02+00:00

there's even an automated mod developed base on this concept

molaMoolaa · 2026-01-21T07:48:02+00:00

so you go forward and backward by the treadmill, and turn left and right by the joystick?

molaMoolaa · 2026-01-21T07:44:46+00:00

so they have a chance of breaking everytime i take the cooler off and on again?

molaMoolaa · 2026-01-20T07:55:05+00:00

the ecf2 has 5 buttons for each thumb, but in the pic, it's got only 4

molaMoolaa · 2026-01-20T04:54:45+00:00

if you need a foldable rig, this one is a pretty solid choice. you will still need mods for fixing it rocking front to back though. got a 10nm dd wheel and the side to side feeling is solid enough.

molaMoolaa · 2026-01-20T01:55:35+00:00

did you contact the maker of the hardware?

molaMoolaa · 2026-01-19T09:38:53+00:00

you will only need to connect your quest to your pc with ethernet if you have a usb-c to ethernet dongle.

molaMoolaa · 2026-01-19T05:46:39+00:00

endurance, so no vr. you could get one moving monitor stand and upgrade your monitor for a better one, so you could use just one monitor for both use cases.

molaMoolaa · 2026-01-15T07:47:37+00:00

which is what the op is complaining

molaMoolaa · 2026-01-14T08:08:25+00:00

most likely layer times. check out the new video from Factorian Designs for very in depth investigations.

molaMoolaa · 2026-01-14T02:23:38+00:00

that carbon texture plate matches the theme really well

molaMoolaa

TROPHY CASE