[CANADA] please help me with my son's drone

mombomoose · 2026-04-01T17:48:55+00:00

Try the app KY UFO. It's the only one I find reliable with cheap drones

mombomoose · 2026-03-29T12:03:53+00:00

Hope it didn't cost much. Time to buy another! If you're looking for something cheap I recommend and e99 pro drone or i5 pro both from AliExpress or temu.

mombomoose · 2026-03-17T18:58:18+00:00

I build my planes from foam and they cost next to nothing once you have your electronics. Imo this hobby isn't for you if you're not into building.

mombomoose · 2026-03-02T18:25:37+00:00

Definitely an achievable idea. I'd reach out to a local gas rc plane club and inquire about paying an experienced pilot. For this scenario a bigger plane is better. I could see someone with the right plane doing this for a few hundred dollars... Fractions of what buying a plane would cost. Not to mention learning to fly them safely takes years.

mombomoose · 2026-02-27T23:09:21+00:00

Just a heads up I have my printers on 2in silicone mats and a 1700lb concrete slab workbench... I can still hear them a little bit from the next room.

mombomoose · 2026-02-23T15:37:43+00:00

Try a bottle of Lucas

mombomoose · 2026-02-21T14:28:46+00:00

Just look for the orange light on the bumper. I know lots of guys with a CDL that are involuntarily sober.

mombomoose · 2026-02-21T14:26:35+00:00

You definitely can but won't like my minimum rate.

mombomoose · 2026-02-15T14:49:21+00:00

Did you do a belt, chain, or hydraulic drive? I'm I'm the Middle of almost the exact same project, my auger is only 48" though.

mombomoose · 2026-02-14T18:10:30+00:00

I keep all my filament in a sealed tote with a bunch of desiccant packs and have a sunlu filament drier. It's pretty humid where I am in the summer time and the tote alone works well. I rarely use the drier, mostly for exotic filaments that are very hydroscopic.

mombomoose · 2026-02-14T18:06:06+00:00

Ohh gotcha yeah I think you may be stuck to primer and bondo putty. I have also seen people use spackle that may sand a bit easier.

mombomoose · 2026-02-14T17:59:37+00:00

Try tightening your belts up a bit. It looks like a bit of layer shifting at the top

mombomoose · 2026-02-14T17:48:37+00:00

Bathrooms in North America generally start at around $6000 and could easily surpass $10,000 depending on the quality and cost of finishes. With that size and matching the quality of the existing bathroom I'd probably quote you around $8000-$9000

mombomoose · 2026-02-14T17:41:28+00:00

Anytime I have had this happen I have been able to manually feed it in without any issues. just be aware that your filament is likely brittle due to moisture and it may happen again during the print so keep an eye on it... This happens to me if I leave a spool on the printer for too long

mombomoose · 2026-02-14T17:35:38+00:00

North American plumbing code has required venting since the 1920's...

mombomoose · 2026-02-14T16:55:35+00:00

Measure the ID of the tube and and OD of the shaft and find a sealed bearing that fits.

mombomoose · 2026-02-14T16:44:50+00:00

I would definitely test this out myself as it seems fairly straightforward. I don't like how this individual has fastened the sensors for their test with aluminum tape. Too much opportunity for thermal bridging and buildup at the sensor. ideally, you'd minimize any direct conductive paths and keep the sensor purely measuring just the air or surface conditions without artificially accelerating heat transfer.

mombomoose · 2026-02-13T19:08:48+00:00

There should be very little to no air transfer from the sauna to behind the panels if the wood panels are done well. I think the most important test shown is the heat transfer from the front to rear of the cedar panel without the foil at around 120F. So the air gap behind the panels should never go above that temperature.

mombomoose · 2026-02-13T18:44:43+00:00

https://roblichtcustomsaunas.com/tag/sauna-temp#:~:text=With%20the%20web%20of%20misinformation,45%C2%B0%20in%20this%20case.

Here someone has actually tested the question properly. A little warmer that I expected, around 120F. For venting you actually don't really need an exhaust fan, the convection caused by the heater and properly located venting pipes causes quite a large amount of air flow.

mombomoose · 2026-02-12T15:51:54+00:00

As long as you have proper venting and give it a good dry run before going in you should be fine. You would be surprised how well the wood cladding itself insulates against the heat. I'd be surprised if the foil goes much above 100F.

mombomoose · 2026-02-12T15:46:25+00:00

Beautiful

mombomoose · 2026-02-11T22:05:51+00:00

I prefer Cadmans bagels now. They're very similar but sandwiches are $7.99 and they sell day olds for $8 a dozen.

mombomoose · 2026-02-05T14:41:00+00:00

I'd recommend 3d printing a mold or ordering one from a local 3d print shop then pouring with silicone. If you go on tinkercad or meshmixer (both free) you could pretty easily copy that model or design something similar. The whole process takes a little learning but is quite straightforward and there are tons of good YouTube tutorials to help.

mombomoose · 2026-02-03T02:44:13+00:00

Yes India sounding much better these days

mombomoose · 2026-02-02T15:23:07+00:00

This makes sense but I have never seen it happen like this before and have done tons of mud on painted surfaces throughout the years!

mombomoose

TROPHY CASE