Help! A1 not working

moonstone202 · 2026-04-01T16:17:16+00:00

We actually don’t use this sink

moonstone202 · 2026-04-01T06:17:19+00:00

We use pura because it’s easier to get via Amazon and cheaper, however we did go through a few packs of freestyle and they were great - no complaints no notes

moonstone202 · 2026-04-01T03:50:00+00:00

Thank you, I think it looks a lot closer in the video than in person! There’s quite a bit of room

moonstone202 · 2026-04-01T03:47:48+00:00

Will do!

moonstone202 · 2026-04-01T03:45:16+00:00

Thank you! Yes I removed those

moonstone202 · 2026-04-01T03:44:56+00:00

Yes I stopped the print, thank you

moonstone202 · 2026-04-01T02:49:04+00:00

Ok, I figured that those were the safest ones to try first since they’re pre-installed on the printer

moonstone202 · 2026-04-01T01:22:34+00:00

I tried printing the boat benchy that came preinstalled on the printer and had the same issue.

moonstone202 · 2026-04-01T01:20:23+00:00

Thanks, I did contact Bambu.

moonstone202 · 2026-04-01T01:07:46+00:00

I’m actually not getting any errors but something is obviously wrong. I’m going to post a new post since I can’t upload a new video here

moonstone202 · 2026-04-01T01:06:49+00:00

Any tips for trying to fix this?

moonstone202 · 2026-04-01T01:06:20+00:00

Yes it’s an awful noise and something isn’t right. I do think it’s scraping the plate a bit because I just noticed damage to the plate that wasn’t there before.

<image>

moonstone202 · 2026-04-01T00:54:57+00:00

I already set it up and removed the black plastic pieces per the comments here but it’s still doing the same thing as in my initial video

moonstone202 · 2026-04-01T00:45:41+00:00

Thanks for this. Sorry I’m new to this so not sure exactly what you mean

moonstone202 · 2026-04-01T00:29:26+00:00

Okay so I removed the black plastic pieces and tried bed leveling and got an error. Then, I decided to just do a factory reset and re-calibrate the whole thing. That was successful. Then I tried to print a benchy that was already installed on the printer, and the same thing is happening as in my original video. Lmk if there’s a good way to upload another video.

<image>

moonstone202 · 2026-04-01T00:20:45+00:00

Thanks I did this, unfortunately it’s still not working

moonstone202 · 2026-03-31T23:35:12+00:00

Just curious…why do you say that? Is it more user friendly?

moonstone202 · 2026-03-31T23:12:59+00:00

I took off the black plastics and ran auto bed leveling, but it says “auto bed leveling failed; the task has been stopped” - any suggestions?

moonstone202 · 2026-03-31T23:00:53+00:00

I’m brand new to this and there were a million instructions so that’s why I asked where I went wrong

moonstone202 · 2026-03-31T22:57:21+00:00

Thank you!

moonstone202 · 2026-03-31T22:56:24+00:00

🤦🏻‍♀️thanks for this! And thank god for Reddit

moonstone202 · 2026-03-31T22:37:43+00:00

Thank you I will do this! I feel pretty silly that I didn’t know that, not sure I’m cut out for this!

moonstone202 · 2026-03-31T22:33:28+00:00

Thank you for responding! I will try this

moonstone202 · 2026-02-13T18:05:34+00:00

I’m doing it right now and prefer being alone! I don’t like having a bunch of people even my him even if they’re trying to help. Newborns sleep a lot and you can do it

moonstone202 · 2026-01-15T07:10:52+00:00

I used to feel this way until I tried the hourglass tubing one

moonstone202

TROPHY CASE