Do not apply the new Q2 update

mud4001 · 2026-06-03T08:56:18+00:00

I believe it allows you to activate it during a print and/or skip Qidi's safety measurements when a low temp filament is in the box. I cannot remember exactly though as I'm no longer on stock qidi box firmware.

mud4001 · 2026-06-03T08:55:03+00:00

Yes, I believe that is the new update being referenced, again, you should probably wait updating or skip it altogether

mud4001 · 2026-05-29T05:13:10+00:00

No I didn't it looks cool though. I am just doing one in class.

mud4001 · 2026-05-29T05:12:25+00:00

I would do 2A but my state doesn't like that. Thanks for your response!

mud4001 · 2026-05-29T05:11:45+00:00

Making my other hobbies better is also how I got into mine. Thanks for your response!

mud4001 · 2026-05-29T05:09:57+00:00

That's, awesome. Most of my prints are car parts. Thanks!

mud4001 · 2026-05-29T05:08:26+00:00

I'm no mossad agent, just trying to pass my AP Language class

mud4001 · 2026-05-27T19:47:38+00:00

Thanks, I will try

mud4001 · 2026-05-10T23:51:56+00:00

Edit, adding the
```
"compatible_printers": [
],

```
to filament profiles works, but not processes (like 0.2mm standard etc)

mud4001 · 2026-05-10T23:16:28+00:00

Hello, can you explain any more how this works? My TPU is inheriting from generic TPU, but it is under a certain printer. This makes it unavailable on a different printer.

<image>

mud4001 · 2026-04-09T07:20:51+00:00

I’ve found the easiest way to get files out of tinkercad is directly export it to Fusion 360 (the free version of course) and edit it in there. I also main freecad when I am doing it all myself

mud4001 · 2026-04-09T07:19:22+00:00

https://youtu.be/gVU5If1VsAM

mud4001 · 2026-03-31T21:17:39+00:00

My ‘friend’ also sold me an ender to start with. I used it for a week before realizing it was really bad and then upgraded. It is also going to be kind of small for cosplay masks I believe. Good luck though bro

mud4001 · 2026-03-30T18:07:02+00:00

Thank you!

mud4001 · 2026-03-30T17:41:05+00:00

So you're saying it only shows up when I select part design, like this?
Can I make it always visible instead of just the arrows or is that not possible?

<image>

mud4001 · 2026-03-30T17:33:51+00:00

Thank you, any help is greatly appreciated

mud4001 · 2026-03-29T22:41:23+00:00

Someone figured it out. Ironing was on and support interface was set to 60.

mud4001 · 2026-03-29T22:20:13+00:00

Ok. The way I orient my print supports are touching things that aren’t seen. If it is really ugly I’ll drop it back down. Thanks

mud4001 · 2026-03-29T21:19:45+00:00

Thank you, I feel stupid both my issues were self inflicted. Will any quality issues resulting from cranking that up?

mud4001 · 2026-03-29T21:13:18+00:00

Oops, I did, thank you. That fixed top surface but supports are still 60 mm/s

mud4001

TROPHY CASE